Export limit exceeded: 369872 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (369872 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-72037 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: net: lan743x: Initialize eth_syslock spinlock before use lan743x_hardware_init() calls pci11x1x_strap_get_status() during the PCI11x1x probe sequence. That helper acquires the Ethernet subsystem hardware lock via lan743x_hs_syslock_acquire(), which relies on adapter->eth_syslock_spinlock to serialize access. The spinlock is currently initialized only after the strap status is read. With CONFIG_DEBUG_SPINLOCK enabled, taking the zeroed initialized spinlock can trip the spinlock debug check. Fix by initializing adapter->eth_syslock_spinlock before reading the strap status so the probe path never attempts to lock an uninitialized spinlock. | ||||
| CVE-2026-72054 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: net: ip_vti: require CAP_NET_ADMIN in the device netns for changelink vti_changelink() operates on at most two netns, dev_net(dev) and the tunnel link netns t->net. They differ once the device is created in or moved to a netns other than the one the request runs in. The rtnl changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a caller privileged there but not in t->net can rewrite a tunnel that lives in t->net. Gate vti_changelink() on rtnl_dev_link_net_capable() at its top, before any attribute is parsed. | ||||
| CVE-2026-72062 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: gpio: mt7621: avoid corruption of shared interrupt trigger state The bank-shared fields like 'rising' and 'falling' are modified using non-atomic read-modify-write operations. Since every gpio chip instance represents an entire bank of 32 pins, if 'mediatek_gpio_irq_type()' is called concurrently for different IRQs on the same bank a possible overwrite of each other's configuration is possible. Thus, protect this state with 'gpio_generic_lock_irqsave' lock in the same way it is handled in irp_chip 'mediatek_gpio_irq_mask()' and 'mediatek_gpio_irq_unmask()' callbacks. | ||||
| CVE-2026-72064 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: net: mana: Sync page pool RX frags for CPU MANA allocates RX buffers from page pool fragments when frag_count is greater than 1. In that case the buffers remain DMA mapped by page pool and the RX completion path does not call dma_unmap_single(). As a result, the implicit sync-for-CPU normally performed by dma_unmap_single() is missing before the packet data is passed to the networking stack. This breaks RX on configurations which require explicit DMA syncing, for example when booted with swiotlb=force. Fix this by recording the page pool page and DMA sync offset when the RX buffer is allocated, and syncing the received packet range for CPU access before handing the RX buffer to the stack. | ||||
| CVE-2026-72068 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: posix-cpu-timers: Use u64 multiplication in update_rlimit_cpu() update_rlimit_cpu() converts the RLIMIT_CPU value to nanoseconds with u64 nsecs = rlim_new * NSEC_PER_SEC; On 32-bit kernels both rlim_new (unsigned long) and NSEC_PER_SEC (1000000000L) are 32-bit, so the multiplication is performed in unsigned long and truncated for rlim_new > 4 seconds before being widened to u64. The same file already casts to u64 for the matching computation in check_process_timers(): u64 softns = (u64)soft * NSEC_PER_SEC; As a result, the truncated value is installed into the CPUCLOCK_PROF expiry cache (nextevt), causing the process CPU timer to be programmed to fire prematurely for any RLIMIT_CPU soft limit >= 5 seconds. The actual SIGXCPU/SIGKILL decision in check_process_timers() already casts to u64 and is therefore correct, so limit enforcement is not broken; only the expiry-cache programming is wrong. Apply the same cast here so both paths convert rlim_cur identically. 64-bit kernels are unaffected. | ||||
| CVE-2026-68462 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: bpf: Reject negative const offsets for buffer pointers The verifier rejects variable offsets for PTR_TO_TP_BUFFER and PTR_TO_BUF accesses, but it currently accepts a constant negative offset produced by pointer arithmetic. Commit 022ac0750883 ("bpf: use reg->var_off instead of reg->off for pointers") moved constant pointer offsets from reg->off to reg->var_off. However, __check_buffer_access() continued to check only the instruction offset. An access with reg->var_off equal to -8 and an instruction offset of zero therefore passes verification. For writable raw tracepoints, the access end is also calculated from the unsigned reg->var_off.value. An eight-byte access starting at -8 wraps the calculated end to zero, allowing the program to load and attach without increasing max_tp_access. After ensuring that reg->var_off is constant, calculate the effective access start using signed arithmetic and reject it when it is negative. Use the validated start to calculate the access end for both PTR_TO_TP_BUFFER and PTR_TO_BUF. | ||||
| CVE-2026-68463 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: mmc: sdhci-esdhc-imx: use pm_runtime_resume_and_get() in suspend Replace pm_runtime_get_sync() with pm_runtime_resume_and_get() to simplify error handling. pm_runtime_resume_and_get() automatically drops the usage counter on failure, avoiding the need for a separate pm_runtime_put_noidle() call. If it fails, the device is unclocked and accessing hardware registers would cause a kernel panic, so return the error immediately. | ||||
| CVE-2026-68465 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: mmc: sdhci-esdhc-imx: fix esdhc_change_pinstate() to allow default state restore esdhc_change_pinstate() checks for pins_100mhz and pins_200mhz at the top of the function and returns -EINVAL if either is not defined. This prevents the default case from ever being reached, which means devices with a sleep pinctrl state but without high-speed pin states (100mhz/ 200mhz) can never restore their default pin configuration. Move the IS_ERR checks for pins_100mhz and pins_200mhz into their respective switch cases. | ||||
| CVE-2026-68467 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: mtd: mchp23k256: use SPI match data for chip caps The driver stores chip capacity information in both the OF match table and the SPI id table. Probe currently uses of_device_get_match_data(), so a non-OF SPI modalias match falls back to mchp23k256_caps even when the SPI id table selected a different part. Use spi_get_device_match_data() so SPI id-table driver_data is consumed when OF match data is absent. This keeps the existing default fallback while avoiding the wrong MTD geometry for id-table-only matches. | ||||
| CVE-2026-68471 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: wifi: ieee80211: validate MLE common info length ieee80211_mle_common_size() uses the first common-info octet as the common information length for all known MLE types. However, ieee80211_mle_size_ok() only validates that octet for Basic, Probe Request, and TDLS MLEs. Reconfiguration MLEs also skipped the length octet when calculating the minimum common size, and Priority Access MLEs skipped validation of the advertised common information length. Account for the Reconfiguration common-info length octet and validate the advertised common information length for all known MLE types. Keep unknown-type handling unchanged. [remove now misleading comment] | ||||
| CVE-2026-68475 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: reset: sunxi: fix memory region leak on ioremap failure In sunxi_reset_init(), when ioremap() fails, the memory region obtained via request_mem_region() is not released, leading to a resource leak. Add an err_mem_region label to properly release the memory region before freeing the data structure. | ||||
| CVE-2026-68476 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ipvs: reload ip header after head reallocation __ip_vs_get_out_rt() calls skb_ensure_writable() which may reallocate skb->head. | ||||
| CVE-2026-68479 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btrtl: validate firmware patch bounds rtlbt_parse_firmware() copies patch_length - 4 bytes before appending the firmware version. A malformed firmware patch shorter than the version field can make this subtraction underflow and turn the copy into an oversized read and write during Bluetooth setup. The existing patch_offset + patch_length check can also wrap on 32-bit architectures. Validate the patch length and range without arithmetic overflow before allocating or copying the patch. | ||||
| CVE-2026-72008 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: pmdomain: mediatek: Fix possible nullptr KP in HWV cleanup/on-check Should probe fail for HW_VOTER type power domains, this driver was unconditionally trying to perform cleanup for DIRECT_CTL domains, but only after checking if the target domain is powered on... with the DIRECT_CTL scpsys_domain_is_on() code again. And there's more: the scpsys_domain_is_on() function is also being unconditionally used in the probe path, for any power domain that has flag MTK_SCPD_KEEP_DEFAULT_OFF! This bug was never experienced by anyone because the HWV domains never failed probe, and because none of those is declared with the aforementioned flag - but it's still something critical. In order to fix this, add a check for MTCMOS Type and, based on that, call the correct functions for an "is on" check, and also do the same for the cleanup path, calling the correct functions for the "power off" action. For the latter, since there's a call to pm_genpd_remove() right before calling power_off, be cautious and add a variation of the power off functions (with a _internal suffix) for those to get a pointer to scpsys_domain instead of one to generic_pm_domain as, even if that's still working, this is way too much fragile and would break at some point. | ||||
| CVE-2026-72009 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: pmdomain: imx93-blk-ctrl: Extract PHY as shared domain for DSI/CSI The MIPI DSI and CSI domains share control bits for clock and reset, which can lead to incorrect behavior if one domain disables the shared resource while the other is still active. To fix the issue, introduce a shared MIPI PHY power domain to own the common resources and make DSI and CSI its subdomains. This ensures the shared bits are properly managed and not disabled while still in use. | ||||
| CVE-2026-72010 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: cgroup/cpuset: rebind mm mempolicy to effective_mems, not mems_allowed Creating a child cpuset where cpuset.mems is never set leads to a div/0 when a VMA mempolicy with MPOL_F_RELATIVE_NODES rebinds in response to a CPU hotplug event. Reproduction steps: 1) Create a cgroup w/ cpuset controls (do not set cpuset.mems) 2) Move the task into the child cpuset 3) Create a VMA mempolicy for that task with MPOL_F_RELATIVE_NODES 4) unplug and hotplug a cpu echo 0 > /sys/devices/system/cpu/cpu1/online echo 1 > /sys/devices/system/cpu/cpu1/online 5) mempolicy rebind does a div/0 in mpol_relative_nodemask on the call to __nodes_fold() The cpuset code passes (cs->mems_allowed) which is not guaranteed to have nodes to the rebind routine. Use cs->effective_mems instead, which is guaranteed to have a non-empty nodemask once we reach that code path. [ david: add a comment, slightly rephrase description ] | ||||
| CVE-2026-72011 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: s390/diag: Add missing array_index_nospec() call to memtop_get_page_count() 'level' is user space controlled and used to read from an array. Add the missing array_index_nospec() call to prevent speculative execution. | ||||
| CVE-2026-72013 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: riscv: Prevent NULL pointer dereference in machine_kexec_prepare() A NULL pointer dereference issue is noticed in riscv's machine_kexec_prepare(), where image->segment[i].buf might be NULL and copied unchecked. The NULL buf comes from ima_add_kexec_buffer(), where kbuf is added by kexec_add_buffer(), but kbuf.buffer is NULL, then it is copied without a check in machine_kexec_prepare(): kexec_file_load -> kimage_file_alloc_init() -> kimage_file_prepare_segments() -> ima_add_kexec_buffer() -> kexec_add_buffer() -> machine_kexec_prepare() -> memcpy() Address this by adding a check before the data copy attempt. | ||||
| CVE-2026-72079 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: Input: ims-pcu - fix use-after-free and double-free in disconnect ims_pcu_disconnect() only intended to perform cleanup when the primary (control) interface is unbound. However, it currently relies on the interface class to distinguish between control and data interfaces. A malicious device could present a data interface with the same class as the control interface, leading to premature cleanup and potential use-after-free or double-free. Switch to verifying that the interface being disconnected is indeed the control interface. | ||||
| CVE-2026-72082 | 1 Linux | 1 Linux Kernel | 2026-08-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: scsi: elx: efct: Fix refcount leak in efct_hw_io_abort() When efct_hw_reqtag_alloc() fails in efct_hw_io_abort(), the error path returns -ENOSPC without releasing the reference obtained via kref_get_unless_zero() earlier in the function. All other error paths correctly drop the reference. This causes a permanent reference leak on the io_to_abort object. Additionally, the abort_in_progress flag is left set to true on this path, which means future abort attempts for the same I/O will immediately return -EINPROGRESS even though the abort was never submitted, effectively blocking recovery. Fix this by adding the missing kref_put() call and reset abort_in_progress to false, matching the cleanup done in the efct_hw_wq_write() failure path below. | ||||