| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: rxrpc_verify_data ensure rx_dec_buffer alloc
rxrpc_recvmsg_data() calls rxrpc_verify_data() whenever the
rxrpc_call.rx_dec_buffer is unallocated and assumes that upon
successful return that rx_dec_buffer must be allocated.
However, rxrpc_verify_data() does not request an allocation if
the rxrpc_skb_priv.len is zero.
In addition, failure to allocate rx_dec_buffer will result in a
call to skb_copy_bits() with a NULL destination which can
trigger a NULL pointer dereference.
To prevent these issues rxrpc_verify_data() is modified to
always attempt to allocate the rxrpc_call.rx_dec_buffer if it
is NULL.
This issue was identified with assistance of a private
sashiko instance. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Don't move a peeked OOB message onto the pending queue
rxrpc_recvmsg_oob() takes a received oob message off recvmsg_oobq and,
if a response is needed, moves it onto the pending_oobq tree. However,
only the unlink from recvmsg_oobq is guarded by MSG_PEEK; the move onto
pending_oobq always runs.
As a result, reading a challenge with MSG_PEEK leaves the skb on
recvmsg_oobq while also adding it to pending_oobq. Since struct
sk_buff's rbnode shares storage with its next and prev pointers,
rb_insert_color() overwrites the list linkage, and the skb, which holds
a single reference, becomes reachable from both queues at once.
When the socket is closed both queues are drained in turn. While
draining recvmsg_oobq, __skb_unlink() follows the next and prev
pointers that rbnode has overwritten and writes to a bad address. Also,
as the skb holds a single reference but is freed from each queue, both
the skb and the connection reference it holds are released twice. This
leads to memory corruption and to a use-after-free caused by the
connection refcount underflow.
MSG_PEEK does not consume the message from the queue, so only unlink it
from recvmsg_oobq and then move it onto pending_oobq or free it when
the message is actually consumed. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix UAF in rxgk_issue_challenge()
Fix rxgk_issue_challenge() to free the page containing the challenge
content after invoking the tracepoint as the whdr passed to the tracepoint
points into the page just freed. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix potential infinite loop in rxrpc_recvmsg()
Fix the wait in rxrpc_recvmsg() also take check the oob queue. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix ACKALL packet handling
rxrpc_input_ackall() accepts ACKALL packets without checking whether the
call is in a state that can legitimately have outstanding transmit buffers.
A forged ACKALL can therefore reach a new service call in
RXRPC_CALL_SERVER_RECV_REQUEST before any reply packets have been queued.
In that state call->tx_top is zero and call->tx_queue is NULL, so
rxrpc_rotate_tx_window() dereferences a NULL txqueue and triggers a
null-pointer dereference.
Fix the handling of ACKALL packets by the following means:
(1) Add two new call states: RXRPC_CALL_CLIENT_PRE_SEND which indicates
that the client call is connected, but nothing has been transmitted as
yet; and RXRPC_CALL_CLIENT_AWAIT_ACK, which indicates that everything
has been transmitted at least once, but we're now waiting for the
stuff remaining in the Tx buffer to be ACK'd (retransmissions may
still happen).
The RXRPC_CALL_CLIENT_PRE_SEND state is set when the call is assigned
a channel and transitions to RXRPC_CALL_CLIENT_SEND_REQUEST when the
first packet is transmitted.
RXRPC_CALL_CLIENT_AWAIT_REPLY is then narrowed in scope to indicate
that all Tx packets have been ACK'd and we're now waiting for the
reply to be received.
(2) As per Wyatt Feng's original patch[1], the ACKALL handler then checks
that the call state is one in which there might be stuff in the Tx
buffer to ACK, but now this includes AWAIT_ACK rather than
AWAIT_REPLY. ACKALL packets are ignored if received in the wrong
state.
Note that unlike Wyatt Feng's patch, it's no longer necessary to check
to see if the Tx buffer exists as this the state set now covers this.
(3) Make the ACKALL handler use call->tx_transmitted rather than
call->tx_top as the former is explicitly the highest packet seq number
transmitted, whereas the latter has a looser definition.
Thanks to Jeffrey Altman for a description of the history of the ACKALL
packet[1]. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix the reception of a reply packet before data transmission
Fix rxrpc_receiving_reply() to handle the reception of an apparent reply
DATA packet before rxrpc has had a chance to send any request DATA packets
on a client call by checking to see if the call has been exposed yet by
sending the first packet.
Without this, rxrpc_rotate_tx_window() might oops.
Also fix rxrpc_rotate_tx_window() to handle the Tx queue being empty by
changing the do...while loop into a while loop, just in case a call is
abnormally terminated by an early reply before the last request packet is
transmitted. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix double unlock in rxrpc_recvmsg()
Fix a double unlock in rxrpc_recvmsg() when dealing with OOB messages. |
| In the Linux kernel, the following vulnerability has been resolved:
afs: Fix netns teardown to cancel the preallocation charger
Fix the teardown of an afs network namespace to make sure it cancels the
work item that keeps the preallocated rxrpc call/conn/peer queue charged
before incoming calls are disabled (i.e. listen 0).
Also, if net->live is false because the afs netns is being deleted, make
afs_charge_preallocation() skip charging and make afs_rx_new_call() avoid
requeuing the charger.
(This was found by AI review). |
| In the Linux kernel, the following vulnerability has been resolved:
afs: handle CB.InitCallBackState3 requests without a server record
The cache manager callback path now attaches the server record to an
incoming call through the rxrpc peer's app data. That association is
not guaranteed to exist for every callback request, and most callback
handlers already tolerate that case.
Make CB.InitCallBackState3 follow the same pattern by checking whether a
server record was attached before using it. If the peer is not mapped
to a server record, trace the request and ignore it, matching the
existing behaviour for other unmatched callback requests.
This keeps the callback handler consistent with the rest of the cache
manager service and avoids depending on peer state that may not be
available for a given request. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: Adjust size for copy_to_user()
The amount of data returned to user space should be limited by the buffer
size provided by the application. If the buffer is smaller than the data
size, return only the portion that fits instead of failing. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/radeon: fix integer overflow in radeon_align_pitch()
radeon_align_pitch() has the same kind of overflow issue as the old
amdgpu helper: both the alignment round-up add and the final
'aligned * cpp' calculation can overflow signed int.
If that wraps, radeon_mode_dumb_create() can end up returning an
invalid pitch or creating a zero-sized dumb buffer.
Fix this by using check_add_overflow() for the alignment round-up and
check_mul_overflow() for the final pitch calculation, returning 0 on
overflow. Also reject zero pitch and size in
radeon_mode_dumb_create().
Found via AST-based call-graph analysis using sqry. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: fix wrong pci_get_drvdata type in AER handlers
rtw89 stores an ieee80211_hw pointer via pci_set_drvdata() at probe
time, but io_error_detected() and io_resume() retrieve it as a
net_device pointer. This causes netif_device_detach/attach to
operate on an ieee80211_hw struct, reading and writing at wrong
offsets. The adjacent io_slot_reset() already does it correctly.
Use ieee80211_stop_queues/wake_queues instead, consistent with
every other queue stop/start path in the driver.
Tested on RTL8852CE by calling the handlers from a test module
before and after the fix. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: fix wrong pci_get_drvdata type in AER handlers
rtw88 stores an ieee80211_hw pointer via pci_set_drvdata() at probe
time, but io_error_detected() and io_resume() retrieve it as a
net_device pointer. This causes netif_device_detach/attach to
operate on an ieee80211_hw struct, reading and writing at wrong
offsets.
Use ieee80211_stop_queues/wake_queues instead, consistent with
every other queue stop/start path in the driver. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: Correct data type for scan index to avoid infinite loop
A kernel soft lockup was observed during Wi-Fi scanning on the 6GHz band.
The CPU becomes stuck in rtw89_hw_scan_add_chan_ax for over 20 seconds,
leading to a system panic.
RIP points to 0f b6 c3 (movzbl %bl, %eax), which zero-extends
the low 8 bits of RBX into RAX.
RBX (the counter i) has reached a huge value: 0x137466a1.
watchdog: BUG: soft lockup - CPU#2 stuck for 26s! [kworker/u16:4:6124]
Workqueue: events_unbound cfg80211_wiphy_work [cfg80211]
RIP: 0010:rtw89_hw_scan_add_chan_ax+0xb3/0x6e0 [rtw89_core]
Code: a0 48 89 45 a8 44 89 6d 9c 44 89 75 98 eb 29 66 66 2e 0f 1f
84 00 00 00 00 00 66 66 2e 0f 1f 84 00 00 00 00 00 66 90 83 c3 01
<0f> b6 c3 41 3b 44 24 74 0f 83 0b 02 00 00 0f b6 c3 48 8d 14 80 49
RSP: 0018:ffffcb48cbaa39f8 EFLAGS: 00000202
RAX: 0000000000000005 RBX: 00000000137466a1 RCX: 0000000000000000
RDX: ffff89ffc9d851a8 RSI: 0000000000004f0d RDI: 0000000096af0130
RBP: ffffcb48cbaa3a60 R08: 0000000000000000 R09: ffff8a00b7502080
R10: ffff8a00b75ff600 R11: 0000000000000000 R12: ffff89ffc7553870
R13: ffff8a00b7ac8f19 R14: ffff8a00b75020d8 R15: ffff89ffc3d54d80
FS: 0000000000000000(0000) GS:ffff8a014f962000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007558d7f9f4c4 CR3: 0000000178040001 CR4: 00000000001706f0
Call Trace:
<TASK>
rtw89_hw_scan_prep_chan_list_ax+0x8a/0x400 [rtw89_core]
rtw89_hw_scan_start+0x546/0x8a0 [rtw89_core]
? rtw89_fw_h2c_default_cmac_tbl+0x13c/0x1f0 [rtw89_core]
rtw89_ops_hw_scan+0xae/0x120 [rtw89_core]
drv_hw_scan+0xbb/0x180 [mac80211]
__ieee80211_start_scan+0x2fc/0x750 [mac80211]
ieee80211_request_scan+0xe/0x20 [mac80211]
ieee80211_scan+0x123/0x190 [mac80211]
rdev_scan+0x40/0x110 [cfg80211]
cfg80211_scan_6ghz+0x5a1/0xa30 [cfg80211]
By objdump with source:
for (i = 0; i < req->n_6ghz_params; i++) {
5fbc0: 83 c3 01 add $0x1,%ebx --> i++
5fbc3: 0f b6 c3 movzbl %bl,%eax --> get counter
fbc6: 41 3b 44 24 74 cmp 0x74(%r12),%eax
* RBX: 00000000137466a1 -> %bl = a1 -> EAX = 000000a1 (161) |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: fix OOB read from firmware RX descriptor exceeding DMA buffer
In rtw_pci_rx_napi(), new_len is computed as the sum of pkt_len (14-bit
descriptor field, max 16383) and pkt_offset (drv_info_sz + shift, both
firmware-controlled). The result can exceed RTK_PCI_RX_BUF_SIZE (11478),
causing an out-of-bounds read from the pre-allocated DMA buffer when
skb_put_data copies new_len bytes. The USB transport already validates
this (rtw_usb_rx_data_put checks against RTW_USB_MAX_RECVBUF_SZ); the
PCIe path does not.
Add a check that new_len does not exceed the DMA buffer size. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: add bounds check on firmware mac_id in link lookup
The mac_id field in RX descriptors is 8 bits wide (0-255), but
assoc_link_on_macid[] has only RTW89_MAX_MAC_ID_NUM (128) entries.
While the driver currently assigns mac_id values below 128, the
descriptor value comes from firmware and is not validated before use
as an array index. Add a defensive bounds check in
rtw89_assoc_link_rcu_dereference() to guard against out-of-range
firmware values. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: fix OOB access from firmware tx status queue ID
ath_tx_edma_tasklet() accesses sc->tx.txq[ts.qid] where ts.qid is a
4-bit hardware field (0-15), but the txq array only has
ATH9K_NUM_TX_QUEUES (10) entries. A qid >= 10 causes an OOB array
access.
Add a bounds check on ts.qid before using it as an array index. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: cancel SSR work items during PCI shutdown
A reboot can crash the kernel if it overlaps with WLAN firmware crash
recovery (SSR). The crash is a NULL pointer dereference in the MHI teardown
path while freeing DMA-backed MHI contexts.
Simplified trace:
dma_free_attrs
mhi_deinit_dev_ctxt [mhi]
ath11k_pci_power_down [ath11k_pci]
ath11k_pci_shutdown [ath11k_pci]
device_shutdown
kernel_restart
On the host side, SSR is driven by the MHI RDDM callback, which queues
reset_work to perform device recovery. reset_work power-cycles the device
by calling ath11k_hif_power_down() followed by ath11k_hif_power_up(). The
power-down phase deinitializes MHI and frees DMA resources.
Shutdown/reboot runs fully asynchronously with this RDDM-driven SSR
recovery flow. As a result, the shutdown path
(ath11k_pci_shutdown() -> ath11k_pci_power_down()) can race with the SSR
recovery sequence.
Fix this by canceling SSR-related work items during PCI shutdown, marking
the device as unregistering, and serializing the RDDM callback path that
checks and queues reset_work. This ensures that no new SSR recovery work
can be queued once teardown has started, and that any in-flight recovery
work is fully synchronized before device power-down, preventing MHI
teardown and DMA resource freeing from running more than once.
Note: This issue only affects PCI/MHI-based devices. AHB-based ath11k
devices do not queue reset_work in normal SSR flows.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04866.5-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1 |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: Fix potential null-ptr-deref in vxlan_gro_prepare_receive().
udp_tunnel_sock_release() could set sk->sk_user_data to NULL
while vxlan_gro_prepare_receive() is running.
Let's check if rcu_dereference_sk_user_data() is NULL after
skb_gro_remcsum_init(). |
| In the Linux kernel, the following vulnerability has been resolved:
OPP: Fix race between OPP addition and lookup
A race exists between dev_pm_opp_add_dynamic() and
dev_pm_opp_find_freq_exact():
CPU0 (add) CPU1 (lookup)
------------------------------- ------------------------------
_opp_add()
mutex_lock()
list_add(&new_opp->node, head)
mutex_unlock() _opp_table_find_key()
mutex_lock()
dev_pm_opp_get(opp)
kref_get()
mutex_unlock()
kref_init(&new_opp->kref)
dev_pm_opp_put()
kref_put_mutex()
The newly added OPP is inserted into the list before its kref is
initialized. A concurrent lookup can find this OPP and increment its
reference count while it is still uninitialized, leading to refcount
corruption and a potential premature free.
Fix this by initializing ->kref and ->opp_table before making the OPP
visible via list_add(). This ensures any concurrent lookup observes a
fully initialized object.
[ Viresh: Updated commit log ] |
