| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: xiic: xiic_xfer(): Fix runtime PM leak on error path
The xiic_xfer() function gets a runtime PM reference when the function is
entered. This reference is released when the function is exited. There is
currently one error path where the function exits directly, which leads to
a leak of the runtime PM reference.
Make sure that this error path also releases the runtime PM reference. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: bus: verify partner exists in typec_altmode_attention
Some usb hubs will negotiate DisplayPort Alt mode with the device
but will then negotiate a data role swap after entering the alt
mode. The data role swap causes the device to unregister all alt
modes, however the usb hub will still send Attention messages
even after failing to reregister the Alt Mode. type_altmode_attention
currently does not verify whether or not a device's altmode partner
exists, which results in a NULL pointer error when dereferencing
the typec_altmode and typec_altmode_ops belonging to the altmode
partner.
Verify the presence of a device's altmode partner before sending
the Attention message to the Alt Mode driver. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: avoid referencing uninit memory in ath9k_wmi_ctrl_rx
For the reasons also described in commit b383e8abed41 ("wifi: ath9k: avoid
uninit memory read in ath9k_htc_rx_msg()"), ath9k_htc_rx_msg() should
validate pkt_len before accessing the SKB.
For example, the obtained SKB may have been badly constructed with
pkt_len = 8. In this case, the SKB can only contain a valid htc_frame_hdr
but after being processed in ath9k_htc_rx_msg() and passed to
ath9k_wmi_ctrl_rx() endpoint RX handler, it is expected to have a WMI
command header which should be located inside its data payload.
Implement sanity checking inside ath9k_wmi_ctrl_rx(). Otherwise, uninit
memory can be referenced.
Tested on Qualcomm Atheros Communications AR9271 802.11n .
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Get source vCPUs from source VM for SEV-ES intrahost migration
Fix a goof where KVM tries to grab source vCPUs from the destination VM
when doing intrahost migration. Grabbing the wrong vCPU not only hoses
the guest, it also crashes the host due to the VMSA pointer being left
NULL.
BUG: unable to handle page fault for address: ffffe38687000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
CPU: 39 PID: 17143 Comm: sev_migrate_tes Tainted: GO 6.5.0-smp--fff2e47e6c3b-next #151
Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 34.28.0 07/10/2023
RIP: 0010:__free_pages+0x15/0xd0
RSP: 0018:ffff923fcf6e3c78 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffffe38687000000 RCX: 0000000000000100
RDX: 0000000000000100 RSI: 0000000000000000 RDI: ffffe38687000000
RBP: ffff923fcf6e3c88 R08: ffff923fcafb0000 R09: 0000000000000000
R10: 0000000000000000 R11: ffffffff83619b90 R12: ffff923fa9540000
R13: 0000000000080007 R14: ffff923f6d35d000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff929d0d7c0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffe38687000000 CR3: 0000005224c34005 CR4: 0000000000770ee0
PKRU: 55555554
Call Trace:
<TASK>
sev_free_vcpu+0xcb/0x110 [kvm_amd]
svm_vcpu_free+0x75/0xf0 [kvm_amd]
kvm_arch_vcpu_destroy+0x36/0x140 [kvm]
kvm_destroy_vcpus+0x67/0x100 [kvm]
kvm_arch_destroy_vm+0x161/0x1d0 [kvm]
kvm_put_kvm+0x276/0x560 [kvm]
kvm_vm_release+0x25/0x30 [kvm]
__fput+0x106/0x280
____fput+0x12/0x20
task_work_run+0x86/0xb0
do_exit+0x2e3/0x9c0
do_group_exit+0xb1/0xc0
__x64_sys_exit_group+0x1b/0x20
do_syscall_64+0x41/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
CR2: ffffe38687000000 |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: zoned: fix memory leak after finding block group with super blocks
At exclude_super_stripes(), if we happen to find a block group that has
super blocks mapped to it and we are on a zoned filesystem, we error out
as this is not supposed to happen, indicating either a bug or maybe some
memory corruption for example. However we are exiting the function without
freeing the memory allocated for the logical address of the super blocks.
Fix this by freeing the logical address. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: VMX: Fix crash due to uninitialized current_vmcs
KVM enables 'Enlightened VMCS' and 'Enlightened MSR Bitmap' when running as
a nested hypervisor on top of Hyper-V. When MSR bitmap is updated,
evmcs_touch_msr_bitmap function uses current_vmcs per-cpu variable to mark
that the msr bitmap was changed.
vmx_vcpu_create() modifies the msr bitmap via vmx_disable_intercept_for_msr
-> vmx_msr_bitmap_l01_changed which in the end calls this function. The
function checks for current_vmcs if it is null but the check is
insufficient because current_vmcs is not initialized. Because of this, the
code might incorrectly write to the structure pointed by current_vmcs value
left by another task. Preemption is not disabled, the current task can be
preempted and moved to another CPU while current_vmcs is accessed multiple
times from evmcs_touch_msr_bitmap() which leads to crash.
The manipulation of MSR bitmaps by callers happens only for vmcs01 so the
solution is to use vmx->vmcs01.vmcs instead of current_vmcs.
BUG: kernel NULL pointer dereference, address: 0000000000000338
PGD 4e1775067 P4D 0
Oops: 0002 [#1] PREEMPT SMP NOPTI
...
RIP: 0010:vmx_msr_bitmap_l01_changed+0x39/0x50 [kvm_intel]
...
Call Trace:
vmx_disable_intercept_for_msr+0x36/0x260 [kvm_intel]
vmx_vcpu_create+0xe6/0x540 [kvm_intel]
kvm_arch_vcpu_create+0x1d1/0x2e0 [kvm]
kvm_vm_ioctl_create_vcpu+0x178/0x430 [kvm]
kvm_vm_ioctl+0x53f/0x790 [kvm]
__x64_sys_ioctl+0x8a/0xc0
do_syscall_64+0x5c/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd |
| In the Linux kernel, the following vulnerability has been resolved:
cxl/pmem: Fix nvdimm registration races
A loop of the form:
while true; do modprobe cxl_pci; modprobe -r cxl_pci; done
...fails with the following crash signature:
BUG: kernel NULL pointer dereference, address: 0000000000000040
[..]
RIP: 0010:cxl_internal_send_cmd+0x5/0xb0 [cxl_core]
[..]
Call Trace:
<TASK>
cxl_pmem_ctl+0x121/0x240 [cxl_pmem]
nvdimm_get_config_data+0xd6/0x1a0 [libnvdimm]
nd_label_data_init+0x135/0x7e0 [libnvdimm]
nvdimm_probe+0xd6/0x1c0 [libnvdimm]
nvdimm_bus_probe+0x7a/0x1e0 [libnvdimm]
really_probe+0xde/0x380
__driver_probe_device+0x78/0x170
driver_probe_device+0x1f/0x90
__device_attach_driver+0x85/0x110
bus_for_each_drv+0x7d/0xc0
__device_attach+0xb4/0x1e0
bus_probe_device+0x9f/0xc0
device_add+0x445/0x9c0
nd_async_device_register+0xe/0x40 [libnvdimm]
async_run_entry_fn+0x30/0x130
...namely that the bottom half of async nvdimm device registration runs
after the CXL has already torn down the context that cxl_pmem_ctl()
needs. Unlike the ACPI NFIT case that benefits from launching multiple
nvdimm device registrations in parallel from those listed in the table,
CXL is already marked PROBE_PREFER_ASYNCHRONOUS. So provide for a
synchronous registration path to preclude this scenario. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: at91-pio4: check return value of devm_kasprintf()
devm_kasprintf() returns a pointer to dynamically allocated memory.
Pointer could be NULL in case allocation fails. Check pointer validity.
Identified with coccinelle (kmerr.cocci script).
Depends-on: 1c4e5c470a56 ("pinctrl: at91: use devm_kasprintf() to avoid potential leaks")
Depends-on: 5a8f9cf269e8 ("pinctrl: at91-pio4: use proper format specifier for unsigned int") |
| In the Linux kernel, the following vulnerability has been resolved:
refscale: Fix uninitalized use of wait_queue_head_t
Running the refscale test occasionally crashes the kernel with the
following error:
[ 8569.952896] BUG: unable to handle page fault for address: ffffffffffffffe8
[ 8569.952900] #PF: supervisor read access in kernel mode
[ 8569.952902] #PF: error_code(0x0000) - not-present page
[ 8569.952904] PGD c4b048067 P4D c4b049067 PUD c4b04b067 PMD 0
[ 8569.952910] Oops: 0000 [#1] PREEMPT_RT SMP NOPTI
[ 8569.952916] Hardware name: Dell Inc. PowerEdge R750/0WMWCR, BIOS 1.2.4 05/28/2021
[ 8569.952917] RIP: 0010:prepare_to_wait_event+0x101/0x190
:
[ 8569.952940] Call Trace:
[ 8569.952941] <TASK>
[ 8569.952944] ref_scale_reader+0x380/0x4a0 [refscale]
[ 8569.952959] kthread+0x10e/0x130
[ 8569.952966] ret_from_fork+0x1f/0x30
[ 8569.952973] </TASK>
The likely cause is that init_waitqueue_head() is called after the call to
the torture_create_kthread() function that creates the ref_scale_reader
kthread. Although this init_waitqueue_head() call will very likely
complete before this kthread is created and starts running, it is
possible that the calling kthread will be delayed between the calls to
torture_create_kthread() and init_waitqueue_head(). In this case, the
new kthread will use the waitqueue head before it is properly initialized,
which is not good for the kernel's health and well-being.
The above crash happened here:
static inline void __add_wait_queue(...)
{
:
if (!(wq->flags & WQ_FLAG_PRIORITY)) <=== Crash here
The offset of flags from list_head entry in wait_queue_entry is
-0x18. If reader_tasks[i].wq.head.next is NULL as allocated reader_task
structure is zero initialized, the instruction will try to access address
0xffffffffffffffe8, which is exactly the fault address listed above.
This commit therefore invokes init_waitqueue_head() before creating
the kthread. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: refuse to create ea block when umounted
The ea block expansion need to access s_root while it is
already set as NULL when umount is triggered. Refuse this
request to avoid panic. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: meson_sm: fix to avoid potential NULL pointer dereference
of_match_device() may fail and returns a NULL pointer.
Fix this by checking the return value of of_match_device. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: spi-nor: Fix shift-out-of-bounds in spi_nor_set_erase_type
spi_nor_set_erase_type() was used either to set or to mask out an erase
type. When we used it to mask out an erase type a shift-out-of-bounds
was hit:
UBSAN: shift-out-of-bounds in drivers/mtd/spi-nor/core.c:2237:24
shift exponent 4294967295 is too large for 32-bit type 'int'
The setting of the size_{shift, mask} and of the opcode are unnecessary
when the erase size is zero, as throughout the code just the erase size
is considered to determine whether an erase type is supported or not.
Setting the opcode to 0xFF was wrong too as nobody guarantees that 0xFF
is an unused opcode. Thus when masking out an erase type, just set the
erase size to zero. This will fix the shift-out-of-bounds.
[ta: refine changes, new commit message, fix compilation error] |
| In the Linux kernel, the following vulnerability has been resolved:
bcache: fixup btree_cache_wait list damage
We get a kernel crash about "list_add corruption. next->prev should be
prev (ffff9c801bc01210), but was ffff9c77b688237c.
(next=ffffae586d8afe68)."
crash> struct list_head 0xffff9c801bc01210
struct list_head {
next = 0xffffae586d8afe68,
prev = 0xffffae586d8afe68
}
crash> struct list_head 0xffff9c77b688237c
struct list_head {
next = 0x0,
prev = 0x0
}
crash> struct list_head 0xffffae586d8afe68
struct list_head struct: invalid kernel virtual address: ffffae586d8afe68 type: "gdb_readmem_callback"
Cannot access memory at address 0xffffae586d8afe68
[230469.019492] Call Trace:
[230469.032041] prepare_to_wait+0x8a/0xb0
[230469.044363] ? bch_btree_keys_free+0x6c/0xc0 [escache]
[230469.056533] mca_cannibalize_lock+0x72/0x90 [escache]
[230469.068788] mca_alloc+0x2ae/0x450 [escache]
[230469.080790] bch_btree_node_get+0x136/0x2d0 [escache]
[230469.092681] bch_btree_check_thread+0x1e1/0x260 [escache]
[230469.104382] ? finish_wait+0x80/0x80
[230469.115884] ? bch_btree_check_recurse+0x1a0/0x1a0 [escache]
[230469.127259] kthread+0x112/0x130
[230469.138448] ? kthread_flush_work_fn+0x10/0x10
[230469.149477] ret_from_fork+0x35/0x40
bch_btree_check_thread() and bch_dirty_init_thread() may call
mca_cannibalize() to cannibalize other cached btree nodes. Only one thread
can do it at a time, so the op of other threads will be added to the
btree_cache_wait list.
We must call finish_wait() to remove op from btree_cache_wait before free
it's memory address. Otherwise, the list will be damaged. Also should call
bch_cannibalize_unlock() to release the btree_cache_alloc_lock and wake_up
other waiters. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: 8250_bcm7271: fix leak in `brcmuart_probe`
Smatch reports:
drivers/tty/serial/8250/8250_bcm7271.c:1120 brcmuart_probe() warn:
'baud_mux_clk' from clk_prepare_enable() not released on lines: 1032.
The issue is fixed by using a managed clock. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: serial: imx: disable Ageing Timer interrupt request irq
There maybe pending USR interrupt before requesting irq, however
uart_add_one_port has not executed, so there will be kernel panic:
[ 0.795668] Unable to handle kernel NULL pointer dereference at virtual addre
ss 0000000000000080
[ 0.802701] Mem abort info:
[ 0.805367] ESR = 0x0000000096000004
[ 0.808950] EC = 0x25: DABT (current EL), IL = 32 bits
[ 0.814033] SET = 0, FnV = 0
[ 0.816950] EA = 0, S1PTW = 0
[ 0.819950] FSC = 0x04: level 0 translation fault
[ 0.824617] Data abort info:
[ 0.827367] ISV = 0, ISS = 0x00000004
[ 0.831033] CM = 0, WnR = 0
[ 0.833866] [0000000000000080] user address but active_mm is swapper
[ 0.839951] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
[ 0.845953] Modules linked in:
[ 0.848869] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.1.1+g56321e101aca #1
[ 0.855617] Hardware name: Freescale i.MX8MP EVK (DT)
[ 0.860452] pstate: 000000c5 (nzcv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 0.867117] pc : __imx_uart_rxint.constprop.0+0x11c/0x2c0
[ 0.872283] lr : imx_uart_int+0xf8/0x1ec
The issue only happends in the inmate linux when Jailhouse hypervisor
enabled. The test procedure is:
while true; do
jailhouse enable imx8mp.cell
jailhouse cell linux xxxx
sleep 10
jailhouse cell destroy 1
jailhouse disable
sleep 5
done
And during the upper test, press keys to the 2nd linux console.
When `jailhouse cell destroy 1`, the 2nd linux has no chance to put
the uart to a quiese state, so USR1/2 may has pending interrupts. Then
when `jailhosue cell linux xx` to start 2nd linux again, the issue
trigger.
In order to disable irqs before requesting them, both UCR1 and UCR2 irqs
should be disabled, so here fix that, disable the Ageing Timer interrupt
in UCR2 as UCR1 does. |
| In the Linux kernel, the following vulnerability has been resolved:
MIPS: fw: Allow firmware to pass a empty env
fw_getenv will use env entry to determine style of env,
however it is legal for firmware to just pass a empty list.
Check if first entry exist before running strchr to avoid
null pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/vmem: split pages when debug pagealloc is enabled
Since commit bb1520d581a3 ("s390/mm: start kernel with DAT enabled")
the kernel crashes early during boot when debug pagealloc is enabled:
mem auto-init: stack:off, heap alloc:off, heap free:off
addressing exception: 0005 ilc:2 [#1] SMP DEBUG_PAGEALLOC
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 6.5.0-rc3-09759-gc5666c912155 #630
[..]
Krnl Code: 00000000001325f6: ec5600248064 cgrj %r5,%r6,8,000000000013263e
00000000001325fc: eb880002000c srlg %r8,%r8,2
#0000000000132602: b2210051 ipte %r5,%r1,%r0,0
>0000000000132606: b90400d1 lgr %r13,%r1
000000000013260a: 41605008 la %r6,8(%r5)
000000000013260e: a7db1000 aghi %r13,4096
0000000000132612: b221006d ipte %r6,%r13,%r0,0
0000000000132616: e3d0d0000171 lay %r13,4096(%r13)
Call Trace:
__kernel_map_pages+0x14e/0x320
__free_pages_ok+0x23a/0x5a8)
free_low_memory_core_early+0x214/0x2c8
memblock_free_all+0x28/0x58
mem_init+0xb6/0x228
mm_core_init+0xb6/0x3b0
start_kernel+0x1d2/0x5a8
startup_continue+0x36/0x40
Kernel panic - not syncing: Fatal exception: panic_on_oops
This is caused by using large mappings on machines with EDAT1/EDAT2. Add
the code to split the mappings into 4k pages if debug pagealloc is enabled
by CONFIG_DEBUG_PAGEALLOC_ENABLE_DEFAULT or the debug_pagealloc kernel
command line option. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/srpt: Add a check for valid 'mad_agent' pointer
When unregistering MAD agent, srpt module has a non-null check
for 'mad_agent' pointer before invoking ib_unregister_mad_agent().
This check can pass if 'mad_agent' variable holds an error value.
The 'mad_agent' can have an error value for a short window when
srpt_add_one() and srpt_remove_one() is executed simultaneously.
In srpt module, added a valid pointer check for 'sport->mad_agent'
before unregistering MAD agent.
This issue can hit when RoCE driver unregisters ib_device
Stack Trace:
------------
BUG: kernel NULL pointer dereference, address: 000000000000004d
PGD 145003067 P4D 145003067 PUD 2324fe067 PMD 0
Oops: 0002 [#1] PREEMPT SMP NOPTI
CPU: 10 PID: 4459 Comm: kworker/u80:0 Kdump: loaded Tainted: P
Hardware name: Dell Inc. PowerEdge R640/06NR82, BIOS 2.5.4 01/13/2020
Workqueue: bnxt_re bnxt_re_task [bnxt_re]
RIP: 0010:_raw_spin_lock_irqsave+0x19/0x40
Call Trace:
ib_unregister_mad_agent+0x46/0x2f0 [ib_core]
IPv6: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
? __schedule+0x20b/0x560
srpt_unregister_mad_agent+0x93/0xd0 [ib_srpt]
srpt_remove_one+0x20/0x150 [ib_srpt]
remove_client_context+0x88/0xd0 [ib_core]
bond0: (slave p2p1): link status definitely up, 100000 Mbps full duplex
disable_device+0x8a/0x160 [ib_core]
bond0: active interface up!
? kernfs_name_hash+0x12/0x80
(NULL device *): Bonding Info Received: rdev: 000000006c0b8247
__ib_unregister_device+0x42/0xb0 [ib_core]
(NULL device *): Master: mode: 4 num_slaves:2
ib_unregister_device+0x22/0x30 [ib_core]
(NULL device *): Slave: id: 105069936 name:p2p1 link:0 state:0
bnxt_re_stopqps_and_ib_uninit+0x83/0x90 [bnxt_re]
bnxt_re_alloc_lag+0x12e/0x4e0 [bnxt_re] |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: Fix leak of dev tracker
At the stage of direction checks, the netdev reference tracker is
already initialized, but released with wrong *_put() call. |
| In the Linux kernel, the following vulnerability has been resolved:
debugobjects: Don't wake up kswapd from fill_pool()
syzbot is reporting a lockdep warning in fill_pool() because the allocation
from debugobjects is using GFP_ATOMIC, which is (__GFP_HIGH | __GFP_KSWAPD_RECLAIM)
and therefore tries to wake up kswapd, which acquires kswapd_wait::lock.
Since fill_pool() might be called with arbitrary locks held, fill_pool()
should not assume that acquiring kswapd_wait::lock is safe.
Use __GFP_HIGH instead and remove __GFP_NORETRY as it is pointless for
!__GFP_DIRECT_RECLAIM allocation. |
