| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
mm/hugetlb: fix list corruption in allocate_file_region_entries()
allocate_file_region_entries() tops up resv->region_cache with freshly
allocated file_region descriptors. The allocation uses GFP_KERNEL, so
resv->lock is dropped around it: the new entries are gathered on a
stack-local list head, allocated_regions, and spliced into
resv->region_cache once the lock is re-acquired.
The splice used list_splice(), which moves the entries but does not
re-initialize the source head, so allocated_regions is left pointing at an
entry that now lives on resv->region_cache. The top-up runs in a while
loop that re-checks the cache deficit after re-acquiring the lock. For a
shared mapping the resv_map is shared by every mapper of the hugetlbfs
inode, so a concurrent region_chg()/region_add()/region_del() on the same
resv_map can consume cache entries during the unlocked window and force a
second iteration. That iteration calls list_add() on the stale head and
corrupts the list; with CONFIG_DEBUG_LIST the __list_add_valid() check
trips:
list_add corruption. next->prev should be prev (ffffc900011ff7f8),
but was ffff88814c281460. (next=ffff88814c545640).
kernel BUG at lib/list_debug.c:31!
allocate_file_region_entries+0x191/0x420
region_chg+0x267/0x300
hugetlb_reserve_pages+0x387/0xc80
hugetlbfs_file_mmap+0x2ce/0x3f0
mmap_region+0x1348/0x1a80
do_mmap+0x85e/0xb90
vm_mmap_pgoff+0x18c/0x330
ksys_mmap_pgoff+0x2a1/0x3e0
do_syscall_64+0xd7/0x420
Without CONFIG_DEBUG_LIST the bad list_add() silently links a kernel-stack
address into resv->region_cache, leading to later use-after-free.
This was observed as a real host panic on a dense KVM host where a QEMU
guest-RAM hugetlbfs file was mapped MAP_SHARED by both QEMU and a separate
SPDK/DPDK vhost-user target, generating concurrent region_* traffic on one
shared resv_map.
Use list_splice_init() so the source head is re-initialized empty after
each splice, making the retry loop safe. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Update x2APIC MSR intercepts if AVIC is inhibited while L2 is active
Always update x2APIC MSR intercepts for L1 when AVIC is deactivated, even
if L2 is active and KVM is using a separate MSR bitmap to run L2. If AVIC
is fully enabled prior to running L2, and is then inhibited while L2 is
active (for a VM-scoped inhibit), then KVM will run L1 with AVIC disabled,
but with x2APIC MSR intercepts disabled, i.e. will allow L1 to read most of
the host's APIC state, send arbitrary interrupts, change task priority, and
ultimately trivially DoS the host.
E.g. sending a self-IPI in L1 on HYPERV_REENLIGHTENMENT_VECTOR, 0xee, with
CONFIG_HYPERV=n in the host kernel as a "safe" PoC, yields:
Spurious interrupt (vector 0xee) on CPU#425. Acked
And hacking KVM to abuse kvm_set_posted_intr_wakeup_handler() to register a
handler and WARN on POSTED_INTR_WAKEUP_VECTOR yields:
------------[ cut here ]------------
WARNING: arch/x86/kvm/svm/svm.c:5594 at pi_wakeup_handler+0x9/0x10 [kvm_amd], CPU#156: nested_x2apic_t/316940
CPU: 156 UID: 0 PID: 316940 Comm: nested_x2apic_t Tainted: G S U
Tainted: [S]=CPU_OUT_OF_SPEC, [U]=USER
Hardware name: Google Astoria-Turin/astoria, BIOS 0.20260209.0-0 02/09/2026
RIP: 0010:pi_wakeup_handler+0x9/0x10 [kvm_amd]
Call Trace:
<IRQ>
sysvec_kvm_posted_intr_wakeup_ipi+0x64/0x80
</IRQ>
<TASK>
asm_sysvec_kvm_posted_intr_wakeup_ipi+0x1a/0x20
RIP: 0010:vcpu_run+0x1430/0x1e40 [kvm]
kvm_arch_vcpu_ioctl_run+0x2c1/0x600 [kvm]
kvm_vcpu_ioctl+0x580/0x6b0 [kvm]
__se_sys_ioctl+0x6d/0xb0
do_syscall_64+0x10a/0x480
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x46ff4b
</TASK>
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: pci: Reject adapter interrupt forwarding if already enabled
The MPCIFC instruction doesn't allow registering adapter interrupts without
first unregistering. So reject any request to enable interrupt forwarding
if its already enabled for the zPCI device. This also fixes overwriting and
thus leaking resources when the ioctl is called multiple times for the same
device. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: pci: Fix memory accounting for pinned/unpinned pages
The account_mem() and unaccount_mem() functions call get_uid() which
increments the reference count of struct user_struct on every invocation.
But we don't decrement the count by calling free_uid(). It also
accounted/unaccounted the pages against the current->mm. But its possible
the unaccount_mem() can be called from a different process context than the
one that originally pinned the pages.
Let's fix this by storing the pinning process user_struct and mm_struct
when accounting for pinned pages, and subsequently free these resources
when the pages are unpinned.
[borntraeger@linux.ibm.com: Fixed whitespace] |
| Integer overflow in the Graphics component. This vulnerability was fixed in Firefox 154, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| In the Linux kernel, the following vulnerability has been resolved:
audit: fix potential use-after-free in audit_del_rule()
`audit_del_rule()` destroys `e->rule.exe` via `audit_remove_mark_rule()`
before unlinking the rule from RCU-visible filter lists and waiting for a
grace period. Concurrent readers in `audit_filter()` and
`audit_filter_rules()` still dereference `e->rule.exe`, while the fsnotify
mark can be freed on an independent lifetime path. This creates a
use-after-free window during rule deletion.
Fix this by unlinking the rule from the RCU-visible lists and invoking
`synchronize_rcu()` before calling `audit_remove_mark_rule()` (and other
rule removal helpers). This ensures that all existing RCU readers have
exited the critical section before any underlying resources are destroyed. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: HIDP: reject frames without a transaction header
hidp_recv_ctrl_frame() and hidp_recv_intr_frame() read skb->data[0]
before checking that the L2CAP SDU contains a transaction header. A
connected HIDP peer can send an empty basic-mode SDU and make both paths
use an uninitialized byte from skb tailroom.
KMSAN reports the use in hidp_session_run(), with the uninitialized value
originating in __alloc_skb() through vhci_write(). The control path
produces two reports and the interrupt path produces one.
The byte can also be controlled by a malformed lower-layer packet. If an
HCI ACL packet contains an L2CAP PDU with a declared zero-length payload
followed by an extra 0x15 byte, l2cap_recv_acldata() reduces skb->len to
the declared PDU length before dispatch. The current HIDP path nevertheless
consumes the extra byte as HIDP_TRANS_HID_CONTROL |
HIDP_CTRL_VIRTUAL_CABLE_UNPLUG and terminates the HIDP session. With this
change, the same packet is discarded and a subsequent feature report
request succeeds.
Pull the transaction header with skb_pull_data() and discard frames that
do not contain it. |
| Site isolation issue in the Networking: Cookies component. This vulnerability was fixed in Firefox 154, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: HIDP: validate numbered report payloads
When hidp_get_raw_report() waits for a numbered report,
hidp_process_data() compares the expected report number with skb->data[0].
A connected HIDP peer can reply with only a DATA transaction header,
leaving the skb empty after the header is removed.
KMSAN reports an uninitialized-value use in hidp_session_run(), with the
value originating in __alloc_skb() through vhci_write(). The transaction
header checks remove the empty-frame reports, but this report remains until
the payload check is added.
The comparison can also consume a peer-controlled byte beyond the declared
L2CAP PDU. A DATA | FEATURE response followed by an extra 0x01 byte made
the current code accept that byte as report ID 1 and complete
HIDIOCGFEATURE with a zero-byte result. With this change the malformed
response is rejected with -EIO, while a subsequent valid response still
succeeds.
Require a payload byte before comparing a numbered report ID. Unnumbered
reports continue to accept an empty payload. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: 6fire: Fix UAF at error handling during probe
Although 6fire driver had a few fixes for dealing with the early error
handling during the probe phase, it forgot a pending URB before
freeing the resources, which may lead to a UAF.
This patch addresses it by doing the almost same cleanup procedure
like the normal disconnect phase at the error path. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: fix OOB write in snd_usbmidi_akai_output()
snd_usbmidi_akai_output() computes its fill-loop bound
buf_end = ep->max_transfer - MAX_AKAI_SYSEX_LEN - 1;
as a signed int, so a small device-advertised bulk-OUT max_transfer
makes buf_end negative. The loop guard then compares the u32
urb->transfer_buffer_length against that negative int: the usual
arithmetic conversion turns buf_end into a large unsigned value, so the
guard stays true and each iteration keeps appending SysEx framing and
payload bytes past the end of the URB transfer buffer, which is only
max_transfer bytes long.
A USB device that advertises a tiny bulk-OUT endpoint can therefore
trigger an attacker-length- and content-controlled heap out-of-bounds
write when a process writes to the created /dev/snd/midiC*D* node.
Return early when there is no room for even one SysEx, so the loop is
never entered with a bound that would wrap. The loop is the last
statement of the function, so bailing out is equivalent to it not
running.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> |
| Privilege escalation in the Networking: Cookies component. This vulnerability was fixed in Firefox 154, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Fix DMA buffer out-of-bounds write when fill_max is set
When a USB audio endpoint requests full packet transfers via the fill_max
descriptor flag, data_ep_set_params() promotes ep->curpacksize to
ep->maxpacksize. However, maxsize is left at the original sample-rate
derived value.
Since u->buffer_size is allocated as maxsize * packets, the resulting
DMA buffer is far too small for the requested transfer length. When the
USB host controller streams up to curpacksize bytes per packet, it writes
past the end of the buffer via DMA, corrupting kernel heap memory.
Update maxsize to curpacksize when fill_max is set so that the allocated
DMA buffer size matches the actual transfer request size.
[ changed to reassign maxsize only when ep->fill_max is set -- tiwai ] |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Clamp frame size in implicit-feedback mode
snd_usb_handle_sync_urb() scales received sync packet sizes by the sender's
stride and stores the result directly in out_packet->packet_size[i]. If a
connected USB device sends an oversized sync packet, this frame count can
exceed ep->maxframesize.
The un-clamped frame count then propagates to the playback endpoint queue,
potentially driving packet transfers beyond the endpoint's hardware frame
limits.
Cap the calculated frame count against ep->maxframesize in
snd_usb_handle_sync_urb() to prevent oversized packets from entering the
playback queue. |
| Privilege escalation in the Application Update component. This vulnerability was fixed in Firefox 154 and Thunderbird 154. |
| In the Linux kernel, the following vulnerability has been resolved:
igbvf: Fix leak in TX DMA error cleanup
If an error is encountered while mapping TX buffers, the driver should
unmap any buffers already mapped for that skb.
Because count is incremented before each frag mapping, it will always
match the correct number of unmappings needed when dma_error is reached.
Decrementing count before the while loop in dma_error causes an
off-by-one error. If any mapping was successful before an unsuccessful
mapping, exactly one DMA mapping (the head) would leak.
This bug was introduced by a 2010 fix for an endless loop in dma_error.
All other affected drivers have already been fixed. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: fix socket use-after-free during link group termination
__smc_lgr_terminate() drops conns_lock after finding a connection in
lgr->conns_all, but before taking a reference on its socket. The connection
is embedded in the socket, and its registration reference protects it only
while the connection remains in the tree.
A concurrent close can unregister the connection and drop that reference,
freeing the socket before the termination worker reaches sock_hold().
The race is reachable when close overlaps link group termination.
Local stress testing reproduced the use-after-free and KASAN reported:
BUG: KASAN: slab-use-after-free in __smc_lgr_terminate.part.0 [smc]
Write of size 4 by task kworker/3:3
Workqueue: events smc_lgr_terminate_work [smc]
__smc_lgr_terminate.part.0 [smc]
The socket was allocated by smc_create(), freed through
slab_free_after_rcu_debug(), and was followed by:
refcount_t: addition on 0; use-after-free.
__smc_lgr_terminate.part.0 [smc]
Take the socket reference while conns_lock still protects the tree entry.
The unregister path then cannot drop the last reference until termination
has finished using the socket. |
| Privilege escalation due to use-after-free in the Graphics: Canvas2D component. This vulnerability was fixed in Firefox 154, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ipset: do not update comments from kernel-side hash adds
mtype_resize() copies comment pointers with memcpy(), not the comment
objects themselves. During the window after an entry has been copied but
before the table swap and backlog replay, the old table is still
published for packet-side updates while the replacement-table entry
already holds the same ip_set_comment_rcu pointer.
If xt_SET --add-set ... --exist hits that old entry in this window,
mtype_add() calls ip_set_init_comment() even though packet-side adds
carry no comment payload. That call frees the shared comment through the
old entry, so the replacement-table entry now holds a stale pointer.
When the queued add is replayed on the new table, mtype_add() calls
ip_set_init_comment() again and strlen() dereferences the stale pointer.
Fix this in mtype_add() by skipping ip_set_init_comment() when
ext->target marks a packet-side add. Userspace adds still update
comments, while packet-side adds can no longer free comment storage
shared with a resize copy. |
| Privilege escalation in the Graphics: CanvasWebGL component. This vulnerability was fixed in Firefox 154, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
