| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: fix data race on rx_stamp/rx_ifindex in bcm_rx_handler()
For an rx op subscribed on all interfaces (ifindex == 0), the same op
is registered once in the shared per-netns wildcard filter list, so
bcm_rx_handler() can run concurrently on different CPUs for frames
arriving on different net devices.
op->rx_stamp and op->rx_ifindex were written before bcm_rx_update_lock was
taken, allowing concurrent writers to race each other - including a torn
store of the 64-bit rx_stamp on 32-bit platforms.
Beyond a torn store bcm_send_to_user() must report the timestamp/ifindex
of the very same frame whose content it is delivering. So the assignment
is placed in the same unbroken bcm_rx_update_lock section as the content
comparison.
As a side effect, the RTR-request frame feature (which never reach
bcm_send_to_user()) no longer updates rx_stamp/rx_ifindex, since only
the notification path needs them. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: fix stale rx/tx ops after device removal
RX: an RX_SETUP update(!) for an existing op skipped can_rx_register()
unconditionally, even when a concurrent NETDEV_UNREGISTER had already
torn down its registration (op->rx_reg_dev == NULL). This silently
did not re-enable frame delivery for that updated filter. bcm_rx_setup()
now re-registers in that case, while leaving rx_ops with ifindex = 0
(all CAN devices) which never carry a tracked rx_reg_dev registered as-is.
TX: bcm_notify() only handled bo->rx_ops on NETDEV_UNREGISTER, leaving
tx_ops with an active cyclic transmission re-arming its hrtimer
indefinitely to execute bcm_tx_timeout_handler(). Cancelling the hrtimer
prevents the runaway timer and any injection into a later reused ifindex,
since nothing else calls bcm_can_tx() for the op until an explicit
TX_SETUP update re-arms it.
Unlike bcm_rx_unreg(), which clears the tracked rx_reg_dev for rx_ops,
the ifindex is intentionally left unchanged for tx_ops. bcm_tx_setup()
always rejects ifindex 0, so clearing it would strand the op: neither a
later TX_SETUP (bcm_find_op()) nor TX_DELETE (bcm_delete_tx_op()) could
ever find it again, since both require an exact ifindex match. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: track a single source interface for ANYDEV timeout/throttle ops
An ANYDEV rx op (ifindex == 0) with an active RX timeout and/or
throttle timer has no defined semantics when matching frames arrive
from several interfaces: bcm_rx_handler() can run concurrently for
the same op on different CPUs, racing hrtimer_cancel()/
bcm_rx_starttimer() against bcm_rx_timeout_handler() and causing
spurious RX_TIMEOUT notifications and last_frames corruption. The
same concurrency lets throttled multiplex frames from different
interfaces clobber the single rx_ifindex/rx_stamp fields shared by
the op.
Add op->if_detected to track the first interface that delivers a
matching frame while a timeout/throttle timer is configured, and
reject frames from any other interface for that op. The claim is
decided in bcm_rx_handler() before hrtimer_cancel() touches
op->timer, so a rejected frame can never disturb the claimed
interface's watchdog. RTR-mode ops are excluded via RX_RTR_FRAME,
independent of kt_ival1/kt_ival2, since those may briefly hold a
stale value from an earlier non-RTR configuration.
The claim is released in bcm_notify() on NETDEV_UNREGISTER and in
bcm_rx_setup() when SETTIMER reconfigures the timer values.
A (re-)claim is only possible on CAN devices in NETREG_REGISTERED
dev->reg_state to cover the release in bcm_notify() where reg_state
becomes NETREG_UNREGISTERING until synchronize_net(). |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: validate frame length in bcm_rx_setup() for RTR replies
bcm_tx_setup() validates cf->len against the CAN/CAN FD DLC limits
before installing frames for TX_SETUP, but bcm_rx_setup() never did
the same for the RTR-reply frame configured via RX_SETUP with
RX_RTR_FRAME. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to cause a denial of service due to a stack-based buffer overflow. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: add missing device refcount for CAN filter removal
sashiko-bot remarked a problem with a concurrent device unregistration
in isotp.c which also is present in the bcm.c code. A former fix for raw.c
commit c275a176e4b6 ("can: raw: add missing refcount for memory leak fix")
introduced a netdevice_tracker which solves the issue for bcm.c too.
bcm_release(), bcm_delete_rx_op() and bcm_notifier() relied on
dev_get_by_index(ifindex) to re-find the device for an rx_op before
unregistering its filter. If a concurrent NETDEV_UNREGISTER has already
unlisted the device from the ifindex table, that lookup fails and
can_rx_unregister() is silently skipped, leaving a stale CAN filter
pointing at the soon-to-be-freed bcm_op/socket.
Hold a netdev_hold()/netdev_put() tracked reference on op->rx_reg_dev
from the moment the rx filter is registered in bcm_rx_setup() until it
is unregistered in bcm_rx_unreg(), and use that reference directly in
bcm_release() and bcm_delete_rx_op() instead of re-looking the device
up by ifindex. |
| In the Linux kernel, the following vulnerability has been resolved:
cpu: hotplug: Bound hotplug states sysfs output
states_show() adds CPU hotplug state names into a single sysfs buffer
using sprintf(). With enough registered states, this can write past the
end of the PAGE_SIZE buffer.
Use sysfs_emit_at() so output is bounded. |
| In the Linux kernel, the following vulnerability has been resolved:
macsec: don't read an unset MAC header in macsec_encrypt()
macsec_encrypt() reads the Ethernet header via eth_hdr(skb)
(skb->head + skb->mac_header) to memmove() the 12 source/destination MAC
bytes forward and make room for the SecTAG.
On the AF_PACKET SOCK_RAW + PACKET_QDISC_BYPASS transmit path the skb
reaches the macsec ndo_start_xmit() with the MAC header unset, so
eth_hdr(skb) resolves to skb->head + (u16)~0 and the read is out of
bounds: a 12-byte heap over-read that is also emitted on the wire as the
frame's outer source/destination MAC. KASAN reports a slab-out-of-bounds
read in macsec_start_xmit() on 6.0; on current mainline a CONFIG_DEBUG_NET
build flags it as an unset mac header in skb_mac_header().
On the TX path the L2 header is at skb->data, so use skb_eth_hdr(), added
by commit 96cc4b69581d ("macvlan: do not assume mac_header is set in
macvlan_broadcast()") for exactly this purpose. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/zcrypt: Validate length for CCA AES cipher key requests
cca_cipher2protkey() derives the copy length for the CPRB parameter
block directly from the length field in the key token. Reject the
request early if the token length exceeds the available space in the
parameter block. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to obtain sensitive information due to a byte-count and element-count confusion. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/zcrypt: Validate length for CCA ECC private key requests
cca_ecc2protkey() derives the copy length for the CPRB parameter
block directly from the length field in the key token. Reject the
request early if the token length exceeds the available space in the
parameter block. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: free mapping node on duplicate reloc root insert
__add_reloc_root() allocates a mapping_node before inserting it into
rc->reloc_root_tree. If rb_simple_insert() finds an existing entry, it
returns the existing rb_node and leaves the newly allocated node unlinked.
The error path then returns -EEXIST without freeing the new node. Since
the node was never inserted into reloc_root_tree, the later cleanup in
put_reloc_control() cannot find it either.
Free the newly allocated node before returning -EEXIST.
The callers currently assert that -EEXIST should not happen, so this is a
defensive cleanup for an unexpected duplicate insert path. If the path is
ever reached, the local allocation should still be released. |
| In the Linux kernel, the following vulnerability has been resolved:
ata: sata_dwc_460ex: fix infinite loop in NCQ tag completion bit-scanning
The hand-rolled bit-scanning loop in the NCQ completion path has an
infinite loop bug. When tag_mask has only high bits set (e.g.
0x80000000), the inner while loop left-shifts tag_mask until it
overflows to 0. At that point !(0 & 1) is always true and 0 <<= 1
stays 0, causing an infinite loop in hardirq context with a spinlock
held.
Replace the open-coded bit-scanning with __ffs() which correctly
finds the least significant set bit and is bounded by the width of
the argument. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: Validate vmw_surface_metadata::array_size
This field comes from userspace and should be validated against specific
limits depending on which Shader Model (SM) is available. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to cause a denial of service due to an off-by-one error in bounds checking. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_ffa: Fix NULL dereference in ffa_partition_info_get()
ffa_partition_info_get() passes uuid_str directly to uuid_parse()
without a NULL check. When a caller passes NULL, uuid_parse() ->
__uuid_parse() -> uuid_is_valid() dereferences the pointer, causing
a kernel panic:
| Unable to handle kernel NULL pointer dereference at virtual address
| 0000000000000040
| pc : uuid_parse+0x40/0xac
| lr : ffa_partition_info_get+0x1c/0x94 [arm_ffa]
Add a NULL guard before uuid_parse() so a NULL argument returns
-ENODEV instead of crashing. Callers are expected to always supply
a valid partition UUID, so NULL is not a supported input. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: 8250_mid: Fix NULL function pointer dereference on DNV/ICX-D/SNR platforms
Commit b1b4efea05a5 ("serial: 8250_mid: Disable DMA for selected
platforms") replaced the dnv_board setup and exit callbacks with
PTR_IF(false, ...), which evaluates to NULL. However, the three call
sites in mid8250_probe() and mid8250_remove() unconditionally
dereference these function pointers without NULL checks, causing a NULL
pointer dereference (kernel oops) on any Denverton (DNV), Ice Lake Xeon
D (ICX-D/CDF), or Snowridge (SNR) platform.
Fix this by adding the missing NULL checks before calling the setup and
exit callbacks. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: bound get_version reply decode to front len
handle_get_version_reply() uses msg->front_alloc_len as the decode
boundary for MON_GET_VERSION_REPLY. That is the size of the reused
reply buffer, not the number of bytes actually received.
A truncated reply can therefore pass ceph_decode_need() and decode the
second u64 from stale tail bytes left in the buffer by an earlier
message, causing an uninitialized memory read.
Use msg->front.iov_len as the receive-side decode boundary, matching
other libceph reply handlers and limiting decoding to the bytes that
were actually read from the wire. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to cause a denial of service due to an out-of-bounds write. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: require CAP_NET_ADMIN in the device netns for changelink
A tunnel changelink() operates on at most two netns, dev_net(dev) and
the sticky underlay netns vxlan->net. They differ once the device is
created in or moved to a netns other than the one the request runs in.
The rtnl changelink path checks CAP_NET_ADMIN only against dev_net(dev),
so a caller privileged there but not in vxlan->net can rewrite a vxlan
device whose underlay lives in vxlan->net.
vxlan_changelink() validates and applies the new configuration against
vxlan->net (vxlan_config_validate(vxlan->net, ...)) and can reopen the
underlay socket in that netns, so the same reasoning as the tunnel
changelink series applies here.
Gate vxlan_changelink() with rtnl_dev_link_net_capable(), at the top of
the op before any attribute is parsed, matching ipgre_changelink() and
the rest of the "require CAP_NET_ADMIN in the device netns for
changelink" series.
Found by 0sec automated security-research tooling (https://0sec.ai). |
