| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: fix NULL h_transaction deref in ocfs2_assure_trans_credits
[BUG]
A direct write over unwritten extents can panic the kernel in
ocfs2_assure_trans_credits() when the journal aborts during DIO
completion. The crash is a general protection fault from a NULL pointer
dereference.
[CAUSE]
ocfs2_dio_end_io_write() loops over a direct write's unwritten extents,
marking each written under a single journal handle. If the journal
aborts (for example after an I/O error) while the extent tree is being
updated, the handle is left aborted with its transaction pointer
cleared. The extent merge treats that failure as not critical and
reports success, so the loop keeps using the handle.
ocfs2_assure_trans_credits() reads the handle's remaining credits
without first checking whether the handle is aborted, and that read
dereferences the cleared transaction pointer.
[FIX]
A journal abort is recorded in the handle itself, so callers are
expected to test the handle rather than rely on a returned error.
Make ocfs2_assure_trans_credits() do that, as the other ocfs2 journal
helpers already do, and return -EROFS when the handle is aborted. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: imx: fix locked bus on SMBus block-read of 0 (atomic)
SMBus 3.1 6.5.7 allows a Block Read byte count of 0, but the atomic
(polling) path rejects it as -EPROTO. Worse, it returns without a
NACK+STOP: the next receive cycle has already started, so the target
keeps holding SDA and the bus stays stuck until a power cycle for
this i2c controller.
Reading I2DR to obtain the count likewise arms the next byte on the
count > I2C_SMBUS_BLOCK_MAX path, which also returned -EPROTO directly
and left the bus held.
Handle both: NACK the in-flight dummy byte (TXAK) and extend msgs->len so
the existing last-byte handling emits STOP; the dummy byte is discarded.
A count of 0 is a valid empty block read; a count above
I2C_SMBUS_BLOCK_MAX is still reported as -EPROTO, but only after the bus
has been released.
The interrupt-driven path has the same flaw from a later commit and is
fixed separately, as it carries a different Fixes: tag and stable range. |
| In the Linux kernel, the following vulnerability has been resolved:
xen/gntdev: fix error handling in ioctl
When gntdev_ioctl_map_grant_ref() fails to copy the operation result
back to userspace after successfully adding the mapping to the list,
the error path returns -EFAULT without releasing the reference
acquired by gntdev_alloc_map(). The mapping remains in priv->maps
with a refcount of 1, causing a memory leak and a dangling list
entry.
Additionally, gntdev_add_map() may modify map->index to avoid overlap
with existing mappings. Therefore, the index returned to userspace
must be obtained after gntdev_add_map() completes.
Fix this by holding the mutex across gntdev_add_map(), retrieving
the correct index, and copy_to_user(). If copy_to_user() fails,
remove the mapping from the list and release the reference while
still holding the lock.
Fix these issues by properly handling all error cases. |
| In the Linux kernel, the following vulnerability has been resolved:
NFS: Charge unstable writes by request size, not folio size
nfs_folio_mark_unstable() and nfs_folio_clear_commit() charge and
uncharge NR_WRITEBACK/WB_WRITEBACK by folio_nr_pages(folio) once per
*request* added to or removed from a commit list. This is correct only
when a folio has a single associated request. When pg_test splits a
folio into N sub-folio requests (e.g. pNFS flexfiles striping with a
stripe unit smaller than the folio size, or plain wsize-limited
splitting), each of the N requests independently charges the whole
folio's page count, inflating the accounting by a factor of N per
folio. With large folios and small stripe units this reaches multiple
orders of magnitude: a 2 MiB folio split into 512 4 KiB requests can
charge up to 512x its real size, pushing global dirty+writeback
accounting past the system's dirty threshold and forcing every
buffered writer on the host into the hard-throttle path, including
unrelated in-kernel NFS server threads sharing the box.
Charge each request only for the pages it actually covers. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-apple: Prevent shared tags across queues on Apple A11
On Apple A11, tags of pending commands must be unique across the admin
and IO queues, else the firmware crashes with
"duplicate tag error for tag N", with N being the tag.
Apply the existing workaround for M1 of reserving two tags for the admin
queue to A11. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: fix data race on rx_stamp/rx_ifindex in bcm_rx_handler()
For an rx op subscribed on all interfaces (ifindex == 0), the same op
is registered once in the shared per-netns wildcard filter list, so
bcm_rx_handler() can run concurrently on different CPUs for frames
arriving on different net devices.
op->rx_stamp and op->rx_ifindex were written before bcm_rx_update_lock was
taken, allowing concurrent writers to race each other - including a torn
store of the 64-bit rx_stamp on 32-bit platforms.
Beyond a torn store bcm_send_to_user() must report the timestamp/ifindex
of the very same frame whose content it is delivering. So the assignment
is placed in the same unbroken bcm_rx_update_lock section as the content
comparison.
As a side effect, the RTR-request frame feature (which never reach
bcm_send_to_user()) no longer updates rx_stamp/rx_ifindex, since only
the notification path needs them. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-pcache: reject option groups without values
The pcache target parses optional arguments as name/value pairs. A
table that advertises one optional argument and supplies only a
recognized option name, for example "cache_mode", reaches
parse_cache_opts() with argc == 1. The parser consumes the name,
decrements argc to zero, then calls dm_shift_arg() again for the value.
dm_shift_arg() returns NULL when no arguments remain, and the following
strcmp() dereferences that NULL pointer.
Check that each recognized option has a value before consuming it. This
keeps valid "cache_mode writeback" and "data_crc true/false" tables
unchanged while making malformed tables fail during target construction
with a precise missing-value error. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-integrity: fix leaking uninitialized kernel memory
If hash size is less than device's tuple size, dm-integrity is supposed
to zero the remaining space. There was a bug in the code that zeroing
didn't work. This commit fixes it. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-verity: fix a possible NULL pointer dereference
Fix a possible NULL pointer dereference dm_verity_loadpin_is_bdev_trusted
if the device has no table. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: elx: efct: Fix I/O leak on unsupported additional CDB
efct_dispatch_fcp_cmd() allocates an efct_io before dispatching an
unsolicited FCP command. If the command has an unsupported additional
CDB, the function returns -EIO before handing the IO to the SCSI layer.
Free the allocated IO before returning from this error path. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: ims-pcu - fix use-after-free and double-free in disconnect
ims_pcu_disconnect() only intended to perform cleanup when the primary
(control) interface is unbound. However, it currently relies on the
interface class to distinguish between control and data interfaces.
A malicious device could present a data interface with the same class
as the control interface, leading to premature cleanup and potential
use-after-free or double-free.
Switch to verifying that the interface being disconnected is indeed
the control interface. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: ims-pcu - fix type confusion in CDC union descriptor parsing
The driver currently trusts the bMasterInterface0 from the CDC union
descriptor without verifying that it matches the interface being
probed. This could lead to the driver overwriting the private data of
another interface.
Validate that the control interface found in the descriptor is indeed
the one we are probing. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: libertas_tf: fix use-after-free in lbtf_free_adapter()
lbtf_free_adapter() calls timer_delete(&priv->command_timer), which does
not wait for a running command_timer_fn() callback. lbtf_free_adapter()
runs on the teardown path right before ieee80211_free_hw() frees priv,
both in lbtf_remove_card() and in the probe error path. command_timer is
armed by mod_timer() in lbtf_cmd() whenever a firmware command is sent.
command_timer_fn() dereferences priv. If a command times out as the
device is removed, command_timer_fn() runs concurrently with teardown and
dereferences priv after it has been freed.
This is the same use-after-free that commit 03cc8f90d053 ("wifi: libertas:
fix use-after-free in lbs_free_adapter()") fixed in the sibling libertas
driver. The libertas_tf variant has the identical pattern and was left
unchanged. Use timer_delete_sync() so any in-flight callback completes
before priv is freed. |
| In the Linux kernel, the following vulnerability has been resolved:
posix-cpu-timers: Use u64 multiplication in update_rlimit_cpu()
update_rlimit_cpu() converts the RLIMIT_CPU value to nanoseconds with
u64 nsecs = rlim_new * NSEC_PER_SEC;
On 32-bit kernels both rlim_new (unsigned long) and NSEC_PER_SEC
(1000000000L) are 32-bit, so the multiplication is performed in unsigned
long and truncated for rlim_new > 4 seconds before being widened to u64.
The same file already casts to u64 for the matching computation in
check_process_timers():
u64 softns = (u64)soft * NSEC_PER_SEC;
As a result, the truncated value is installed into the CPUCLOCK_PROF
expiry cache (nextevt), causing the process CPU timer to be programmed
to fire prematurely for any RLIMIT_CPU soft limit >= 5 seconds. The
actual SIGXCPU/SIGKILL decision in check_process_timers() already casts
to u64 and is therefore correct, so limit enforcement is not broken;
only the expiry-cache programming is wrong. Apply the same cast here so
both paths convert rlim_cur identically.
64-bit kernels are unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: tegra: do not call pinctrl for GPIO direction
tegra_gpio_direction_input() and tegra_gpio_direction_output() already
program the GPIO controller direction registers directly. The additional
pinctrl_gpio_direction_input/output() calls do not add a Tegra pinctrl
operation, because the Tegra pinmux ops provide GPIO request/free
handling but no gpio_set_direction hook.
The extra call still enters the pinctrl core and takes pctldev->mutex.
Shared GPIO users can call the direction path while holding their
per-line spinlock, so this otherwise redundant pinctrl direction call can
sleep in an atomic context.
This was found by our static analysis tool and then confirmed by manual
review of tegra_gpio_probe(), the Tegra GPIO direction callbacks and the
Tegra pinctrl ops. The reviewed path has a default non-sleeping
struct gpio_chip while the direction callback still enters the pinctrl
mutex path.
A directed runtime validation kept the same non-sleeping chip registration
and drove:
gpio_shared_proxy_direction_output()
gpiod_direction_output_raw_commit()
tegra_gpio_direction_output()
pinctrl_gpio_direction_output()
Lockdep reported a sleep-in-atomic warning with the shared GPIO spinlock
held and pinctrl_get_device_gpio_range() plus tegra_gpio_direction_output()
on the stack.
Do not mark the whole chip as can_sleep to paper over this: can_sleep
describes whether get()/set() may sleep, and Tegra value access is MMIO.
Remove the redundant pinctrl direction calls and keep pinctrl involvement
in the existing request/free path. |
| In the Linux kernel, the following vulnerability has been resolved:
ieee802154: ca8210: fix pointer truncation in kfifo on 64-bit
ca8210_test_int_driver_write() and ca8210_test_int_user_read() exchange
a kmalloc'd buffer pointer through a struct kfifo, but pass a literal
'4' as the byte count to kfifo_in()/kfifo_out().
This is correct on 32-bit (pointer = 4 bytes), but on 64-bit only the
low 4 bytes of the 8-byte pointer are written into the FIFO. The reader
then reads back 4 bytes into an 8-byte local pointer variable, leaving
the upper 4 bytes uninitialized stack data. The first dereference of
the reconstructed pointer (fifo_buffer[1]) accesses an arbitrary kernel
address and generally results in an oops.
Use sizeof(fifo_buffer) so the byte count matches pointer width on every
architecture.
The driver has no architecture restriction in Kconfig, so any 64-bit
build with CONFIG_IEEE802154_CA8210_DEBUGFS=y is exposed. Issue has
been latent since the driver was added in 2017 because it is most
commonly deployed on 32-bit MCUs.
Found via a custom Coccinelle semantic patch hunting for short-byte
kfifo I/O on byte-mode kfifos used to shuttle pointers. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| In the Linux kernel, the following vulnerability has been resolved:
ipmi: fix refcount leak in i_ipmi_request()
When a caller provides a `supplied_recv` message to i_ipmi_request(),
the function increments the user's `nr_msgs` reference count. If an
error occurs later, the out_err cleanup path only frees the recv_msg
if the function allocated it itself (i.e., !supplied_recv). In the
supplied_recv case the cleanup is skipped, leaving the reference count
elevated. The caller ipmi_request_supply_msgs() does not release the
supplied_recv on error, so the reference is permanently leaked.
Fix this by explicitly reverting the reference count operations when a
supplied recv_msg with a valid user pointer is present in the error
path: decrement nr_msgs and drop the user's kref. |
| In the Linux kernel, the following vulnerability has been resolved:
ata: libata-core: Add NOLPM quirk for PNY CS900 1TB SSD
The PNY CS900 1TB SSD (Phison PS3111-S11, DRAM-less) drops off the bus
after entering Device-Initiated Slumber during idle. With the default
med_power_with_dipm policy the link goes down (SStatus 1 SControl 300)
and does not recover, forcing the filesystem read-only. Forcing
max_performance keeps the link stable across prolonged idle.
Add a NOLPM quirk so link power management is disabled for this drive
specifically, leaving it intact for other devices on the host. |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: probes: save original sp in rethook trampoline
Reading a word from the stack in a kretprobe crashes a risc-v kernel.
$ cd /sys/kernel/tracing/
$ echo 'r n_tty_write $stack0' > dynamic_events
$ echo 1 > events/kprobes/enable
Unable to handle kernel paging request at virtual address 0000000200000128
...
[<ffffffff80016d16>] regs_get_kernel_stack_nth+0x26/0x38
[<ffffffff80177196>] process_fetch_insn+0x3ee/0x760
[<ffffffff80177836>] kretprobe_trace_func+0x116/0x1f0
[<ffffffff8017795a>] kretprobe_dispatcher+0x4a/0x58
[<ffffffff8013572e>] kretprobe_rethook_handler+0x5e/0x90
[<ffffffff80180838>] rethook_trampoline_handler+0x70/0x108
[<ffffffff8001ba32>] arch_rethook_trampoline_callback+0x12/0x1c
[<ffffffff8001ba84>] arch_rethook_trampoline+0x48/0x94
[<ffffffff8067872a>] tty_write+0x1a/0x30
In regs_get_kernel_stack_nth, regs->sp contains an arbitrary value.
arch_rethook_trampoline saves the registers from the probed function in a
struct pt_regs. sp is not saved. Instead, sp is decremented for
arch_rethook_trampoline's local stack.
Fix this crash and save the original sp along with the other registers.
Use a0 as a temporary register, it is overwritten anyway.
[pjw@kernel.org: added Fixes tag; cc'ed stable] |
