| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: add INIT verification after cookie unpacking
In SCTP handshake, the INIT chunk is initially processed by the server
and embedded into the cookie carried in INIT-ACK. The client then
returns this cookie via COOKIE-ECHO, where the server unpacks it and
reconstructs the original INIT chunk.
When cookie authentication is enabled, the cookie contents are protected
against tampering, so reusing the unpacked INIT without re-verification
is safe.
However, when cookie authentication is disabled, the reconstructed INIT
can no longer be trusted. In this case, the INIT must be explicitly
validated after unpacking to avoid processing potentially tampered data.
Add sctp_verify_init() checks after cookie unpacking in COOKIE-ECHO
processing paths (sctp_sf_do_5_1D_ce() and sctp_sf_do_5_2_4_dupcook())
when cookie_auth_enable is disabled. On failure, the new association is
freed and the packet is discarded.
Also tighten cookie validation in sctp_unpack_cookie() by verifying the
embedded chunk type is SCTP_CID_INIT before treating it as an INIT
chunk.
Finally, update sctp_verify_init() to validate parameter bounds using
the actual embedded INIT length instead of chunk->chunk_end, since the
INIT stored in COOKIE-ECHO may not span the entire chunk buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Mask pseudo pointer values in verifier logs
print_bpf_insn() masks ldimm64 immediates for pointer-bearing pseudo
sources when pointer leaks are not allowed, but the mask only covers
BPF_PSEUDO_MAP_FD and BPF_PSEUDO_MAP_VALUE.
BPF_PSEUDO_MAP_IDX, BPF_PSEUDO_MAP_IDX_VALUE, and BPF_PSEUDO_BTF_ID can
also be resolved to kernel pointer values before the verifier log prints
the instruction. Include them in the existing pointer classification so
the log prints 0x0 instead of the rewritten address. |
| In the Linux kernel, the following vulnerability has been resolved:
octeontx2-af: Validate NIX maximum LFs correctly
NIX maximum number of LFs can be set via devlink command
but that can be done before assigning any LFs to a PF/VF.
The condition used to check whether any LFs are assigned is
incorrect. This patch fixes that condition. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_compat: ebtables emulation must reject non-bridge targets
xtables targets return netfilter verdicts: NF_ACCEPT, NF_DROP, and so
on. ebtables targets return incompatible verdicts: EBT_ACCEPT,
EBT_DROP, ... We cannot allow fallback to NFPROTO_UNSPEC.
ebtables doesn't permit this since
11ff7288beb2 ("netfilter: ebtables: reject non-bridge targets")
but that commit missed the nft_compat layer. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: xt_connmark: reject invalid shift parameters
Revision 2 of the CONNMARK target accepts user-controlled shift
parameters and applies them to 32-bit mark values in
connmark_tg_shift().
A shift_bits value of 32 or more triggers an undefined-shift bug when
the rule is evaluated. Invalid shift_dir values are also accepted and
silently fall back to the left-shift path.
Reject invalid revision-2 shift parameters in connmark_tg_check() so
malformed rules fail at installation time, before they can reach the
packet path. |
| In the Linux kernel, the following vulnerability has been resolved:
gue: validate REMCSUM private option length
GUE private flags can indicate that remote checksum offload metadata is
present. The private flags field itself is accounted for by
guehdr_flags_len(), but guehdr_priv_flags_len() currently returns 0 even
when GUE_PFLAG_REMCSUM is set.
This lets a packet with only the private flags field pass
validate_gue_flags(), after which gue_remcsum() and gue_gro_remcsum()
read the missing REMCSUM start/offset fields from the following bytes.
Account for GUE_PLEN_REMCSUM when GUE_PFLAG_REMCSUM is present so that
malformed packets are rejected during option validation. |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: KVM: Check irq validity in kvm_vcpu_ioctl_interrupt()
Function kvm_vcpu_ioctl_interrupt() can be called from userspace, here
add irq validility cheking in kvm_vcpu_ioctl_interrupt(). |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/amd/brs: Fix kernel address leakage
A user-only branch stack can contain branches that originate from
the kernel. As a result, kernel addresses are exposed to user space
even when PERF_SAMPLE_BRANCH_USER is requested. On AMD processors
supporting X86_FEATURE_BRS (Zen 3 only), perf can still report entries
such as SYSRET/interrupt returns for which the branch-from addresses
are in the kernel.
E.g.
$ perf record -j any,u -c 4000 -e branch-brs -o - -- \
perf bench syscall basic --loop 1000 | \
perf script -i - -F brstack|tr ' ' '\n'| \
grep -E '0x[89a-f][0-9a-f]{15}'
...
0xffffffff810001c4/0x72e2e32955eb/-/-/-/0//-
0xffffffff810001c4/0x72e2d94a9821/-/-/-/0//-
0xffffffff810001c4/0x72e2d94ffa1b/-/-/-/0//-
...
BRS provides no hardware branch filtering, so privilege level
filtering is performed entirely in software. However, amd_brs_match_plm()
only validates the branch-to address against the requested privilege
levels. For branches from the kernel to user space, the branch-from
address is left unchecked and is leaked. Extend the software filter to
also validate the branch-from address, so that any branch record whose
branch-from address is in the kernel is dropped when
PERF_SAMPLE_BRANCH_USER is requested. |
| In the Linux kernel, the following vulnerability has been resolved:
VDUSE: avoid leaking information to userspace
The bounceing is not necessarily page aligned, so current VDUSE can
leak kernel information through mapping bounce pages to
userspace. Allocate bounce pages with __GFP_ZERO to avoid leaking
information to userspace. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix overflow in passthrough ioctl bounds check
smb2_ioctl_query_info() validates the PASSTHRU_FSCTL response payload
before copying it to userspace.
The payload offset and length both come from 32-bit fields. The bounds
check currently adds OutputOffset and qi.input_buffer_length directly, so
the addition can wrap in 32-bit arithmetic before the result is compared
against the response buffer length.
A malicious server can use a large OutputOffset and a small OutputCount
to make the wrapped sum pass the bounds check. The later copy_to_user()
then reads from io_rsp + OutputOffset, outside the response buffer.
Use size_add() for the offset plus length check so overflow is treated as
out of bounds. |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: validate DFS referral string offsets
parse_dfs_referrals() validates that the response header and referral
array fit in the received buffer, but each referral also contains string
offsets supplied by the server.
Those offsets are used to compute the DfsPath and NetworkAddress string
pointers without checking whether they still point inside the response
buffer. A malformed referral can therefore make the computed pointer
exceed the end of the buffer. The resulting negative max_len is then
passed to cifs_strndup_from_utf16(), and the non-Unicode path forwards it
to kstrndup() as a size_t, allowing strnlen() to read out of bounds.
Validate each string offset before deriving the string pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
ieee802154: admin-gate legacy LLSEC dump operations
In net/ieee802154/netlink.c, the legacy IEEE802154_NL family ops table
builds the LLSEC dump entries (LLSEC_LIST_KEY, LLSEC_LIST_DEV,
LLSEC_LIST_DEVKEY, LLSEC_LIST_SECLEVEL) with IEEE802154_DUMP() which
sets no .flags, so generic netlink runs them ungated. The modern
nl802154 family admin-gates the equivalent reads via
NL802154_CMD_GET_SEC_KEY and friends with .flags = GENL_ADMIN_PERM.
Any local uid that can open AF_NETLINK / NETLINK_GENERIC can resolve
the "802.15.4 MAC" family and dump LLSEC_LIST_KEY on any wpan netdev
that has an LLSEC key installed; the dump handler writes the raw
16-byte AES-128 key bytes (IEEE802154_ATTR_LLSEC_KEY_BYTES, copied
verbatim from struct ieee802154_llsec_key.key) into the reply.
Recovering the AES key compromises 802.15.4 LLSEC link confidentiality
and authenticity, since LLSEC uses CCM* and the same key authenticates
and encrypts frames.
Impact: any local uid with no capabilities can read the raw 16-byte
AES-128 LLSEC key from the kernel keytable on any wpan netdev that has
an administrator-installed LLSEC key, by issuing an LLSEC_LIST_KEY
dump on the legacy IEEE802154_NL generic-netlink family.
Introduce IEEE802154_DUMP_PRIV() mirroring IEEE802154_DUMP() but
setting .flags = GENL_ADMIN_PERM, and use it for the four LLSEC dump
entries. LIST_PHY and LIST_IFACE retain IEEE802154_DUMP() because the
modern nl802154 family exposes their equivalents to unprivileged
readers by design (NL802154_CMD_GET_WPAN_PHY and
NL802154_CMD_GET_INTERFACE carry "can be retrieved by unprivileged
users" annotations). |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: reject non-resident records for resident-only attributes
The shared lookup-time attribute validator rejects non-resident
$FILE_NAME and $VOLUME_NAME records because their formats require
resident values and callers handle returned records as resident
attributes. Other resident-only attribute types still pass through the
generic non-resident mapping-pairs checks.
That leaves real resident/non-resident union confusion paths. Inode load
looks up $STANDARD_INFORMATION and then reads data.resident.value_offset
without checking a->non_resident. ntfs_inode_sync_standard_information()
does the same when updating the standard information value.
ntfs_write_volume_flags() also looks up $VOLUME_INFORMATION and reads
data.resident.value_offset directly. $INDEX_ROOT callers in dir.c and
index.c depend on the same lookup contract before consuming the resident
index root value.
Reject non-resident records for all resident-only attribute types in the
shared validator. Keep the existing $FILE_NAME and $VOLUME_NAME behavior,
but factor it through a helper and extend it to
$STANDARD_INFORMATION, $OBJECT_ID, $VOLUME_INFORMATION, $INDEX_ROOT, and
$EA_INFORMATION. For $OBJECT_ID and $EA_INFORMATION this is contract
hardening for resident-only formats; this patch only rejects the
non-resident form and does not add new resident value validation for
those types. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: validate resident index root values on lookup
Resident $INDEX_ROOT values carry index header fields that callers
consume after lookup. Some callers already validate parts of the layout
before walking entries, but those checks are scattered and do not cover
all root header invariants, such as entries_offset alignment and lower
bound, index_length, and allocated_size consistency.
The resident root resize paths now keep these header fields consistent
while the value size changes: ntfs_ir_truncate() lowers
index.allocated_size before shrinking the resident value, and
ntfs_ir_reparent() grows the resident value before publishing a larger
root header. Lookup-time validation can therefore cover these invariants
without tripping over the driver's own resize paths.
Add $INDEX_ROOT to the minimum resident value size table and validate the
resident index header fields before returning the attribute from lookup.
Require 8-byte aligned index header fields, a sane entries_offset, an
index_length within allocated_size, allocated_size within the resident
value, and enough entry space for at least an index entry header.
The shared validator already rejects non-resident records for
resident-only attribute types, including $INDEX_ROOT. |
| In the Linux kernel, the following vulnerability has been resolved:
fpga: microchip-spi: fix zero header_size OOB read in mpf_ops_parse_header()
mpf_ops_parse_header() reads header_size from the bitstream at
MPF_HEADER_SIZE_OFFSET (24). When header_size is zero, the expression
*(buf + header_size - 1) reads one byte before the buffer start.
Since initial_header_size is set to 71 in mpf_ops, the fpga-mgr core
guarantees the buffer is large enough to reach MPF_HEADER_SIZE_OFFSET.
The only real gap is the zero header_size case, which cannot be
resolved by providing a larger buffer, so return -EINVAL. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: validate frame length in bcm_rx_setup() for RTR replies
bcm_tx_setup() validates cf->len against the CAN/CAN FD DLC limits
before installing frames for TX_SETUP, but bcm_rx_setup() never did
the same for the RTR-reply frame configured via RX_SETUP with
RX_RTR_FRAME. |
| In the Linux kernel, the following vulnerability has been resolved:
NFS: Charge unstable writes by request size, not folio size
nfs_folio_mark_unstable() and nfs_folio_clear_commit() charge and
uncharge NR_WRITEBACK/WB_WRITEBACK by folio_nr_pages(folio) once per
*request* added to or removed from a commit list. This is correct only
when a folio has a single associated request. When pg_test splits a
folio into N sub-folio requests (e.g. pNFS flexfiles striping with a
stripe unit smaller than the folio size, or plain wsize-limited
splitting), each of the N requests independently charges the whole
folio's page count, inflating the accounting by a factor of N per
folio. With large folios and small stripe units this reaches multiple
orders of magnitude: a 2 MiB folio split into 512 4 KiB requests can
charge up to 512x its real size, pushing global dirty+writeback
accounting past the system's dirty threshold and forcing every
buffered writer on the host into the hard-throttle path, including
unrelated in-kernel NFS server threads sharing the box.
Charge each request only for the pages it actually covers. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: ims-pcu - fix type confusion in CDC union descriptor parsing
The driver currently trusts the bMasterInterface0 from the CDC union
descriptor without verifying that it matches the interface being
probed. This could lead to the driver overwriting the private data of
another interface.
Validate that the control interface found in the descriptor is indeed
the one we are probing. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: use parsed transport offset in SCTP state lookup
set_sctp_state() reads the SCTP chunk header again in order to drive the
IPVS SCTP state table. For IPv6 it computes the offset with
sizeof(struct ipv6hdr), while the surrounding IPVS code uses iph.len from
ip_vs_fill_iph_skb(), where ipv6_find_hdr() has already skipped
extension headers and found the real transport header.
This makes the state machine read from the wrong offset for IPv6 SCTP
packets that carry extension headers. For example, an INIT packet with an
8-byte destination options header can be scheduled correctly by
sctp_conn_schedule(), but set_sctp_state() reads the first byte of the
SCTP verification tag as a DATA chunk type. The connection then moves
from NONE to ESTABLISHED instead of INIT1, gets the longer established
timeout, and updates the active/inactive destination counters
incorrectly. This happens even though the SCTP handshake has not
completed.
Use the parsed transport offset passed down from ip_vs_set_state() for
the SCTP chunk-header lookup. For IPv4 and IPv6 packets without
extension headers this preserves the existing offset. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: validate extension-frame layout before RX
Extension frames only have the extension header at the regular 802.11
header offset. The generic RX path can still reach helpers and interface
dispatch code that read regular header address fields before unsupported
extension subtypes are dropped.
mac80211 currently only handles S1G beacon extension frames. Drop other
extension subtypes before they can reach regular-header RX processing.
For S1G beacons, linearize the SKB with the management-frame path and
require the fixed S1G beacon header, including optional fixed fields
indicated by frame control, before generic RX dispatch.
Route S1G beacons through the station/default-link RX path without
regular-header station lookup. Avoid regular-header address reads in the
mac80211 RX paths that process S1G extension beacons, including
accept-frame, duplicate-detection, address-copy, and MLO
address-translation paths.
Also make ieee80211_get_bssid() length-safe before returning the S1G
source-address pointer. |
