| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
can: kvaser_usb_leaf: kvaser_usb_leaf_wait_cmd(): validate received command extents
The wait and bulk receive paths walk variable-length commands from a
USB buffer. A nonzero command shorter than CMD_HEADER_LEN can still be
dispatched, and the wait path copies a matching command into a fixed
caller-owned struct kvaser_cmd using the device-provided length.
Reject nonzero commands that do not contain the fixed header or that
extend beyond the current USB buffer item. In the wait path, also reject
a matching command that exceeds the destination before copying it. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: prevent peer transport count overflow
sctp_assoc_add_peer() increments the association's 16-bit transport_count
for every new unique peer. Adding the 65,536th transport wraps the count to
zero.
SCTP sock_diag uses transport_count to reserve the INET_DIAG_PEERS payload,
then copies one sockaddr_storage for every entry in transport_addr_list.
After the wrap, a diagnostic dump reserves an empty payload and writes
8 MiB of peer addresses past the skb tail.
Reject a new unique peer when transport_count has reached U16_MAX. Perform
the check after the existing-peer lookup so a duplicate address continues
to return its existing transport at the limit. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp - Fix snp_filter_reserved_mem_regions() off-by-one
Sashiko notes:
> regarding the bounds check in snp_filter_reserved_mem_regions()
> called via walk_iomem_res_desc(): does the check
> if ((range_list->num_elements * 16 + 8) > PAGE_SIZE)
> allow an off-by-one heap buffer overflow?
>
> If range_list->num_elements is 255, 255 * 16 + 8 = 4088, which is <= 4096.
> Writing range->base (8 bytes) fills 4088-4095, but writing range->page_count
> (4 bytes) would write to 4096-4099, overflowing the kzalloc-allocated
> PAGE_SIZE buffer.
Fix this by accounting for the entry about to be written to, in addition to
the entries that are already allocated. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: fix OOB read from firmware RX descriptor exceeding DMA buffer
In rtw_pci_rx_napi(), new_len is computed as the sum of pkt_len (14-bit
descriptor field, max 16383) and pkt_offset (drv_info_sz + shift, both
firmware-controlled). The result can exceed RTK_PCI_RX_BUF_SIZE (11478),
causing an out-of-bounds read from the pre-allocated DMA buffer when
skb_put_data copies new_len bytes. The USB transport already validates
this (rtw_usb_rx_data_put checks against RTW_USB_MAX_RECVBUF_SZ); the
PCIe path does not.
Add a check that new_len does not exceed the DMA buffer size. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: fix wrong pci_get_drvdata type in AER handlers
rtw88 stores an ieee80211_hw pointer via pci_set_drvdata() at probe
time, but io_error_detected() and io_resume() retrieve it as a
net_device pointer. This causes netif_device_detach/attach to
operate on an ieee80211_hw struct, reading and writing at wrong
offsets.
Use ieee80211_stop_queues/wake_queues instead, consistent with
every other queue stop/start path in the driver. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: sun4i-ss - Remove insecure and unused rng_alg
Remove sun4i_ss_rng, as it is insecure and unused:
- It has multiple vulnerabilities. sun4i_ss_prng_seed() is missing
locking and has a buffer overflow. sun4i_ss_prng_generate() fails to
fill the entire buffer with cryptographic random bytes, because it
rounds the destination length down and also doesn't actually wait for
the hardware to be ready before pulling bytes from it.
- No user of this code is known. It's usable only theoretically via the
"rng" algorithm type of AF_ALG. But userspace actually just uses the
actual Linux RNG (/dev/random etc) instead. And rng_algs don't
contribute entropy to the actual Linux RNG either. (This may have
been confused with hwrng, which does contribute entropy.)
The sun4i_ss_prng_seed() buffer overflow was reported by Tianchu Chen
and discovered by Atuin - Automated Vulnerability Discovery Engine
There's no point in fixing all these vulnerabilities individually when
this is unused code, so let's just remove it. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: validate DRAW_PRIMITIVES header size before division
vmw_cmd_draw() computes
maxnum = (header->size - sizeof(cmd->body)) / sizeof(*decl);
where header->size is u32 and is taken straight from the user-supplied
command stream. When header->size is less than sizeof(cmd->body) the
unsigned subtraction wraps to nearly 4 GiB, producing a huge maxnum.
Any user-controlled cmd->body.numVertexDecls then passes the bound and
the loop dereferences decl[i] far past the end of the kernel command
bounce buffer, producing an out-of-bounds read of kernel memory.
Reject undersized headers up front. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/panthor: reject firmware sections with oversized data
In panthor_fw_load_section_entry(), the data size to copy is calculated
without validating it against the allocated section_size:
section->data.size = hdr.data.end - hdr.data.start;
If a crafted firmware sets data.size larger than the allocated memory,
this could cause a heap buffer overflow in panthor_fw_init_section_mem()
memcpy(section->mem->kmap, section->data.buf, section->data.size);
Additionally, if the section->data.size exceeds the BO size, could this
memset underflow the size calculation, leading to a massive out-of-bounds
zeroing of kernel memory?
memset(section->mem->kmap + section->data.size, 0,
panthor_kernel_bo_size(section->mem) - section->data.size);
Reject section entries whose initial data is larger than the section size. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Fix out-of-bounds write in irdma_copy_user_pgaddrs
The irdma_copy_user_pgaddrs function loops through all of the umem DMA
blocks to populate the PBLEs and will stop when either the last DMA
block is reached or palloc->total_cnt is reached. The issue is that
the logic for checking palloc->total_cnt would only work for non-zero
values.
When irdma_setup_pbles is called with lvl==0, it
calls irdma_copy_user_pgaddrs with palloc->total_cnt==0, which means
the only way to break out of the loop is to reach the last umem DMA
block, which means it could end up going beyond the fixed size of 4
iwmr->pgaddrmem array that is used in the lvl==0 case.
In the case of QP/CQ/SRQ rings, the value of lvl is determined by a
separate input (for example, req.cq_pages in the case of a CQ). So,
we must perform explicit checking to ensure we don't overflow the
pgaddrmem array if the user provides a umem that consists of more
blocks than their provided req.cq_pages. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Bound synthetic-field strings with seq_buf
The synthetic field helpers build a prefixed synthetic variable name and
a generated hist command in fixed MAX_FILTER_STR_VAL buffers. The
current code appends those strings with raw strcat(), so long key lists,
field names, or saved filters can run past the end of the staging
buffers.
Build both strings with seq_buf and propagate -E2BIG if either the
synthetic variable name or the generated command exceeds
MAX_FILTER_STR_VAL. This keeps the existing tracing-side limit while
using the helper intended for bounded command construction.
[ sdr: Moved struct seq_buf *s for upside-down x-mas tree formatting ] |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: fix OOB access from firmware tx status queue ID
ath_tx_edma_tasklet() accesses sc->tx.txq[ts.qid] where ts.qid is a
4-bit hardware field (0-15), but the txq array only has
ATH9K_NUM_TX_QUEUES (10) entries. A qid >= 10 causes an OOB array
access.
Add a bounds check on ts.qid before using it as an array index. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wcn36xx: fix heap overflow from oversized firmware HAL response
The firmware response dispatcher copies all synchronous HAL responses
into the 4096-byte hal_buf without validating the response length. A
response exceeding WCN36XX_HAL_BUF_SIZE causes a heap buffer overflow
with firmware-controlled content.
Add a bounds check on the response length. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: core: fix supplied_from allocations
If dts property power-supplies has multiple values, then accessing to
psy->supplied_from[i-1] in __power_supply_populate_supplied_from will
overrun supplied_from array. |
| In the Linux kernel, the following vulnerability has been resolved:
vhost/vdpa: validate virtqueue index in mmap and fault paths
vhost_vdpa_mmap() and vhost_vdpa_fault() use vma->vm_pgoff as a
virtqueue index for get_vq_notification(), but they do not validate
that the index is smaller than v->nvqs.
The ioctl path already performs both a bounds check and
array_index_nospec(), but the mmap/fault path only checks that the
index fits in u16. This allows an out-of-range queue index to reach
driver-specific get_vq_notification() callbacks.
Fix this by extracting a unified vhost_vdpa_get_vq_notification()
helper that validates the queue index against v->nvqs and applies
array_index_nospec() before calling the driver callback. Both the
mmap and fault paths use this helper, and the bounds checking is
consolidated into a single location.
From source inspection, the most defensible impact is out-of-bounds
access in the callback path, potentially leading to invalid PFN
remaps and crash/DoS. |
| In the Linux kernel, the following vulnerability has been resolved:
ixgbe: do not configure xps for XDP queues
netif_set_xps_queue() should not be called for an XDP Tx queue, since such
queues are not netdev-exposed. On systems with number of CPUs >=64, on E610
adapter, netdev is configured with maximum number queue pairs being 63
(due to MSI-X assignment), but configuring XDP results in 64 XDP queues.
So, during XDP program load, when netif_set_xps_queue() is called for the
last XDP queue, we get a WARNING with a call trace and KASAN report
afterwards (if enabled).
[ 2012.699800] WARNING: net/core/dev.c:2854 at __netif_set_xps_queue+0x116a/0x1e40, CPU#36: xdpsock/103668
[...]
[ 2012.700029] RIP: 0010:__netif_set_xps_queue+0x116a/0x1e40
[ 2012.700035] Code: b6 34 06 48 89 f8 83 e0 07 83 c0 01 40 38 f0 7c 09 40 84 f6 0f 85 03 0a 00 00 0f b7 44 24 40 66 43 89 44 6a 18 e9 01 fb ff ff <0f> 0b e9 f2 ee ff ff 44 8b 44 24 44 45 85 c0 74 50 4d 85 e4 0f 84
[ 2012.700040] RSP: 0018:ffff8882369aeb28 EFLAGS: 00010246
[ 2012.700046] RAX: 0000000000000000 RBX: 000000000000003f RCX: 0000000000000000
[ 2012.700050] RDX: 1ffff1111da3d891 RSI: ffff888120e34250 RDI: ffff8888ed1ec488
[ 2012.700054] RBP: ffff888913281560 R08: 0000000000000000 R09: ffff8888ed1ec000
[ 2012.700058] R10: ffff8888a2e83180 R11: 0000000000000000 R12: 0000000000007fa8
[ 2012.700061] R13: 000000000000003f R14: ffff888120e34854 R15: ffff8889132817c8
[ 2012.700065] FS: 00007fc8ea9ff740(0000) GS:ffff88884cefe000(0000) knlGS:0000000000000000
[ 2012.700069] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2012.700073] CR2: 00007f81c8000020 CR3: 00000002299f8006 CR4: 00000000007726f0
[ 2012.700077] PKRU: 55555554
[ 2012.700080] Call Trace:
[ 2012.700084] <TASK>
[ 2012.700087] ? ktime_get+0x61/0x150
[ 2012.700097] ? usleep_range_state+0x133/0x1b0
[ 2012.700108] ? __pfx_usleep_range_state+0x10/0x10
[ 2012.700114] netif_set_xps_queue+0x31/0x50
[ 2012.700119] ixgbe_configure_tx_ring+0x472/0x920 [ixgbe]
[...]
[ 2012.700486] ixgbe_xdp+0x38f/0x750 [ixgbe]
[...]
[ 2012.701094] BUG: KASAN: slab-out-of-bounds in __netif_set_xps_queue+0x1ac5/0x1e40
[ 2012.701100] Write of size 4 at addr ffff88888d43cff8 by task xdpsock/103668
Skip XPS configuration for XDP Tx queues. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: ensure inner headers in ICMP errors are in headroom
Sashiko points out that after stripping the outer headers
with pskb_pull() we should ensure the inner IP headers
in ICMP errors from tunnels are present in the skb headroom
for functions like ipv4_update_pmtu(), icmp_send() and
IP_VS_DBG().
Also, add more checks for the length of the inner headers. |
| In the Linux kernel, the following vulnerability has been resolved:
geneve: gate GRO hint in geneve_gro_complete() on gs->gro_hint
geneve_gro_receive() reads the GRO hint through geneve_sk_gro_hint_off(),
which honours it only when the socket enabled IFLA_GENEVE_GRO_HINT
(gs->gro_hint). geneve_gro_complete() instead calls the low-level
geneve_opt_gro_hint_off() and acts on the hint unconditionally.
On a tunnel without the hint, receive aggregates the frames as plain
ETH_P_TEB while complete still honours an attacker-supplied hint option: it
inflates gh_len by gro_hint->nested_hdr_len (u8) and redirects the dispatch
type, so the inner gro_complete handler runs at nhoff + gh_len, an offset
receive never pulled nor validated, reading out of bounds of the skb head:
BUG: KASAN: slab-out-of-bounds in ipv6_gro_complete (net/ipv6/ip6_offload.c:196)
Read of size 1 at addr ffff88800fe91980 by task exploit/153
ipv6_gro_complete (net/ipv6/ip6_offload.c:196)
geneve_gro_complete (drivers/net/geneve.c:965)
udp_gro_complete (net/ipv4/udp_offload.c:940)
inet_gro_complete (net/ipv4/af_inet.c:1621)
__gro_flush (net/core/gro.c:306)
Gate the complete path on gs->gro_hint too via geneve_sk_gro_hint_off(), so
both paths agree. Tunnels that enable the hint are unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: flowtable: Validate iph->ihl in nf_flow_ip4_tunnel_proto()
Add sanity check for iph->ihl field in nf_flow_ip4_tunnel_proto() before
using it to compute the header size, avoiding out-of-bounds access with
malformed IP headers.
While at it, use iph->protocol instead of the hardcoded IPPROTO_IPIP
constant when setting ctx->tun.proto and reference ctx->tun.hdr_size
when updating ctx->offset. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: bpf: Fix hid_bpf_get_data() range check
hid_bpf_get_data() returns a pointer into the HID-BPF context data when
the caller-provided offset and size fit inside ctx->allocated_size.
The current check adds rdwr_buf_size and offset before comparing the
result against ctx->allocated_size. Since both values are unsigned, a
very large size can wrap the sum below ctx->allocated_size and make the
helper return a pointer even though the requested range is not contained
in the backing buffer.
Use check_add_overflow() to reject wrapped range ends before comparing
the requested range end against ctx->allocated_size. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: nv: Inject SEA if guest VNCR isn't normal memory
When constructing an L1 VNCR mapping, KVM unconditionally uses cacheable
memory attributes, even if the underlying PFN isn't memory. This gets
particularly hairy if the endpoint doesn't support cacheable memory
attributes, potentially throwing an SError on writeback...
While KVM does permit cacheable memory attributes on certain PFNMAP
VMAs, kvm_translate_vncr() isn't currently grabbing the VMA. So do the
simpler thing for now and just reject everything that isn't memory. |
